Forum: Early V8 (1932-53)
03-20-2026, 06:55 PM
|
|
Replies: 13
Views: 526
|
|
Forum: Early V8 (1932-53)
03-20-2026, 05:15 PM
|
|
Replies: 13
Views: 526
Re: front and rear blinkers/turn signals. -ideas?
I use a switch such as #500148 drilled under the dash ,I have a high stop light /Flasher coupled into the circuit using four 50 cent diodes to stop feedback, four flashers on the bumpers . works...
|
|
Forum: Early V8 (1932-53)
03-17-2026, 11:11 PM
|
|
Replies: 4
Views: 273
|
|
Forum: Early V8 (1932-53)
03-09-2026, 11:59 PM
|
|
Replies: 17
Views: 657
Re: Holley 94 Carb on 34 engine
Also remove the mixture jets and suck on them holes with a vacuum cleaner ,you also could remove the carb bend up a length of mig wire to 3/8 right angle and prob the holes inside near the...
|
|
Forum: Early V8 (1932-53)
03-08-2026, 04:01 PM
|
|
Replies: 17
Views: 657
Re: Holley 94 Carb on 34 engine
Make a gasket out of copper to cover the hole ,power vale leak through into the 34 manifold , do not ask me how I know ,Ted
|
|
Forum: Early V8 (1932-53)
12-08-2025, 06:14 PM
|
|
Replies: 22
Views: 1,321
|
|
Forum: Early V8 (1932-53)
12-08-2025, 04:53 PM
|
|
Replies: 22
Views: 1,321
|
|
Forum: Early V8 (1932-53)
09-17-2025, 05:21 PM
|
|
Replies: 79
Views: 4,437
Re: Persistent Fuel Leak - Sediment Bowl Inlet
Fuel line should be coated steel ,But i use copper ,set the feral /olive on a brass seat such as a Stromberg inlet fitting or the female end of your flex line not in the pump .diaphragm
matting...
|
|
Forum: Early V8 (1932-53)
09-16-2025, 12:06 AM
|
|
Replies: 22
Views: 1,742
|
|
Forum: Early V8 (1932-53)
08-18-2025, 03:54 PM
|
|
Replies: 16
Views: 1,304
Re: Aluminum Head Thread Repair
I did this on a 49er on one side tapped it out to the next size ,locked tight stud with a nut ,cast iron head worked great .
|
|
Forum: Early V8 (1932-53)
07-30-2025, 09:11 PM
|
|
Replies: 14
Views: 1,812
Re: 34 Ford coupe converting rumble seat to trunk
I have done mine, this is what I did! , (AS said) ,The stamping for the trunk hinges are at the top (inside ) ,The stamping for the rumble seat hinges are at the bottom (sides) , the handle moves to...
|
|
Forum: Early V8 (1932-53)
07-16-2025, 06:12 PM
|
|
Replies: 6
Views: 3,063
|
|
Forum: Early V8 (1932-53)
07-14-2025, 11:00 PM
|
|
Replies: 6
Views: 3,063
|
|
Forum: Early V8 (1932-53)
07-13-2025, 10:54 PM
|
|
Replies: 6
Views: 3,063
1935/36 pick up
Fitting a 35 grill on a 36 what needs to be changed ,Hood ,Radiator .?? Has any one done this .Thanks ,
|
|
Forum: Early V8 (1932-53)
07-13-2025, 07:54 PM
|
|
Replies: 31
Views: 8,859
Re: Q: 34 Ford Coupe RHD rear window regulator
Some times as far as the wood goes canadian products followed the usa version , eg the RHD Canadian seat frame for the 34 Roadster has the reinforcing strut 3/4 towards the left side not supporting...
|
|
Forum: Early V8 (1932-53)
06-20-2025, 12:33 AM
|
|
Replies: 10
Views: 1,805
Re: Wiring: 1933 Ford conduit tube.
I would think about running those two on the out side of tube or under with two clips as future maintenance on the distributor its better to have the tube and terminals caps removable ,
|
|
Forum: Early V8 (1932-53)
06-19-2025, 10:48 PM
|
|
Replies: 27
Views: 4,697
Re: '36 floor pans?
Kube I am trying to post a picture and pointers of how you can make floor pans that you can do your self , They don't down load . I will try on test thred ,Ted
|
|
Forum: Early V8 (1932-53)
06-19-2025, 07:47 PM
|
|
Replies: 27
Views: 4,697
|
|
Forum: Early V8 (1932-53)
06-18-2025, 10:54 PM
|
|
Replies: 27
Views: 4,697
|
|
Forum: Early V8 (1932-53)
06-12-2025, 11:16 PM
|
|
Replies: 22
Views: 4,004
Re: Ted’s brake floaters
If your drums and shoes are worn you can get this issue ,pack up the slots in the top end of the shoe adjuster links with a rivet or a one inch length of 4 " nail ,bend the end to right angle , Or...
|
|
Forum: Early V8 (1932-53)
05-26-2025, 09:15 PM
|
|
Replies: 83
Views: 14,855
|
|
Forum: Early V8 (1932-53)
05-26-2025, 08:51 PM
|
|
Replies: 83
Views: 14,855
|
|
Forum: Early V8 (1932-53)
05-26-2025, 04:37 PM
|
|
Replies: 83
Views: 14,855
|
|
Forum: Early V8 (1932-53)
05-07-2025, 05:27 PM
|
|
Replies: 9
Views: 1,867
Re: Head lining kit
Try Read and twyman in Auckland ,They have large sheets of chicken foot textured black card https://www.retwine.co.nz/
|
|
Forum: Early V8 (1932-53)
04-22-2025, 06:36 PM
|
|
Replies: 10
Views: 1,845
Re: 1934-1935-1936 Ford Spare Wheel Covers.
A bit of topic lf your interested !I body worked my Chrome trim for my 35 in the day by making a T shaped bit of flat steel welded to a 1/4 round rod . I shaped the flat bit to slide in with a...
|
