Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Page 1 of 20 1 234511 Last »
Showing results 1 to 25 of 500
Search took 0.10 seconds. Search: Posts Made By: Kube
Forum: Model A (1928-31) Today, 08:52 AM
Replies: 20
Views: 784
Posted By Kube
Re: Move A By Yourself

Just bought a new Deere Gator and yes, quite a bit more than a nice Model A.
Forum: Early V8 (1932-53) Today, 07:34 AM
Replies: 11
Views: 252
Posted By Kube
Re: Early Ford emergency brake cable guide tube replacement.

You can get the exact tube size through McMaster-Carr. I did so many of these I had purchased a 3' piece.
Forum: Early V8 (1932-53) Yesterday, 07:54 AM
Replies: 3
Views: 179
Posted By Kube
Re: '39 wire control dash knobs ??

The end at the carburetor I had slipped the "ball and spring" over the wire and soldered a "cup" at the end of the wire. Used a ball end mill to shape it nicely. Worked quite well and smoothly.
Forum: Early V8 (1932-53) 05-28-2024, 08:21 PM
Replies: 3
Views: 179
Posted By Kube
Re: '39 wire control dash knobs ??

Newc, what you have is the early style. No doubt, you knew that.
I too had that style on the wagon I'd restored. I rebuilt what I had. Easy enough.
I bought the choke cable at the local tractor...
Forum: Early V8 (1932-53) 05-27-2024, 11:34 AM
Replies: 9
Views: 456
Posted By Kube
Re: Ford intake with S

Typically, a raised letter, numeral, etc. signifies (IE) the manufacturer, date, mold ID. My guess in this case is this was produced outside of the Ford Motor CO. as a service replacement part....
Forum: Early V8 (1932-53) 05-27-2024, 10:41 AM
Replies: 12
Views: 680
Posted By Kube
Re: What is this ?

Hmmm...very good observation.
Forum: Model A (1928-31) 05-26-2024, 04:36 PM
Replies: 4
Views: 179
Posted By Kube
Re: light switch install

For once methinks correctly!

Thank you kindly.
Forum: Model A (1928-31) 05-26-2024, 02:38 PM
Replies: 4
Views: 179
Posted By Kube
light switch install

Hello men!

Might seem simple to you but I'm kinda a newbie to the Model a world so here goes...
The piece on the end of the horn rod (picture attached) ... gets installed at the 3 and 9 o'clock...
Forum: Early V8 (1932-53) 05-25-2024, 12:08 PM
Replies: 12
Views: 680
Posted By Kube
Re: What is this ?

FYI, The compression fitting is not only unsafe within the brake line, it's illegal.
Forum: Early V8 (1932-53) 05-25-2024, 10:09 AM
Replies: 13
Views: 600
Posted By Kube
Re: Rusted 1940 cab

Do you want photos of the inside of the floor?
Forum: Early V8 (1932-53) 05-25-2024, 09:14 AM
Replies: 10
Views: 349
Posted By Kube
Re: Tail light connectore

Yep. They will work but you will need to grind down the diameter a bit. As is, they will not fit the connector.
Forum: Early V8 (1932-53) 05-25-2024, 07:26 AM
Replies: 13
Views: 559
Posted By Kube
Re: Tips or a product that will clean radiator hoses?

Lacquer thinner & scrubby pad.
Forum: Early V8 (1932-53) 05-23-2024, 04:16 PM
Replies: 10
Views: 362
Posted By Kube
Re: Oil filter emergency bypass

As goofy as it may sound, I have reused the old gasket with a 100% success rate.
Forum: Early V8 (1932-53) 05-22-2024, 04:30 PM
Replies: 11
Views: 574
Posted By Kube
Re: Banjo rear end hub, axle bearings and seals

The reproductions have a sorted history of poor quality. The cages were not (are not?) hardened properly and rather quickly, the cage would fail and the bearings were free to go where they wanted....
Forum: Early V8 (1932-53) 05-22-2024, 08:47 AM
Replies: 4
Views: 313
Posted By Kube
Re: Clutch pedal return spring '40 passenger

Here are two photographs that should help you. Note the hole atop the brace for one end of the spring to attach to.
I believe if you zoom in on the other photograph, you'll be able to see how the...
Forum: Early V8 (1932-53) 05-21-2024, 07:03 PM
Replies: 13
Views: 600
Posted By Kube
Re: Rusted 1940 cab

Found one more. I think that's all I have of what you wanted. Hope it helps...
Forum: Early V8 (1932-53) 05-21-2024, 04:50 PM
Replies: 13
Views: 600
Posted By Kube
Re: Rusted 1940 cab

Do these help?
Forum: Early V8 (1932-53) 05-21-2024, 02:31 PM
Replies: 11
Views: 574
Posted By Kube
Re: Banjo rear end hub, axle bearings and seals

Do NOT buy reproduction caged bearings.
Forum: Early V8 (1932-53) 05-20-2024, 08:48 PM
Replies: 14
Views: 779
Posted By Kube
Re: 1932/36 Condenser replacement.

Yes sir!
Forum: Early V8 (1932-53) 05-20-2024, 07:16 PM
Replies: 14
Views: 779
Posted By Kube
Re: 1932/36 Condenser replacement.

For my cars and those clients that allow me to do what I prefer, I too use the 32's.
I think the last time I bought them; they were about $28. A bargain considering the confidence a guy gets with...
Forum: Early V8 (1932-53) 05-20-2024, 02:15 PM
Replies: 7
Views: 610
Posted By Kube
Re: sagging drivers door -1936 ford tudorsedan

I tend to align doors without the dovetail in place. I don't want to rely on the dovetail moving the door into position.
Forum: Early V8 (1932-53) 05-18-2024, 01:39 PM
Replies: 14
Views: 779
Posted By Kube
Re: 1932/36 Condenser replacement.

I use a Hunt's Magneto condenser. I have used both the 28mfd and 32mfd units. GREAT reliability. With the coil you are using, solder the original "bracket end" on to the condenser and shove the...
Forum: Early V8 (1932-53) 05-18-2024, 01:34 PM
Replies: 12
Views: 521
Posted By Kube
Re: Crab distributor vacuum line

Guys, guys, guys...
That's an incorrect manifold for the 59A. The correct manifold has an integral threaded hole just below the carburetor base. There is a special fitting that allows vacuum to be...
Forum: Early V8 (1932-53) 05-18-2024, 07:33 AM
Replies: 19
Views: 792
Posted By Kube
Re: '46 Coupe 59AB Starter

I would also use it.
Forum: Early V8 (1932-53) 05-17-2024, 09:43 AM
Replies: 7
Views: 288
Posted By Kube
Re: 40 Sedan Deluxe Speaker install - No studs?

That sounds like a good idea Jim.
Showing results 1 to 25 of 500
Page 1 of 20 1 234511 Last »

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:44 PM.