Forum: Model A (1928-31)
Yesterday, 04:35 PM
|
Replies: 4
Views: 254
|
Forum: Model A (1928-31)
Yesterday, 01:54 PM
|
Replies: 4
Views: 254
testing horn
Okay, please tell me if I am incorrect...
To test an authentic horn, I believe all I need to do is connect 6v. to one wire and ground the other.
Yes? No? I'm full of poopy?
Thanks guys.
|
Forum: Early V8 (1932-53)
05-31-2024, 07:42 AM
|
Replies: 10
Views: 312
Re: 41 pu spare tire options
As you did ask for options, I will offer one. I am considering the fact that your truck is not stock so what I suggest will (should) work for you if you choose to go that route.
I have included...
|
Forum: Model A (1928-31)
05-30-2024, 08:52 AM
|
Replies: 24
Views: 1,222
|
Forum: Early V8 (1932-53)
05-30-2024, 07:34 AM
|
Replies: 14
Views: 391
|
Forum: Early V8 (1932-53)
05-29-2024, 07:54 AM
|
Replies: 3
Views: 199
Re: '39 wire control dash knobs ??
The end at the carburetor I had slipped the "ball and spring" over the wire and soldered a "cup" at the end of the wire. Used a ball end mill to shape it nicely. Worked quite well and smoothly.
|
Forum: Early V8 (1932-53)
05-28-2024, 08:21 PM
|
Replies: 3
Views: 199
Re: '39 wire control dash knobs ??
Newc, what you have is the early style. No doubt, you knew that.
I too had that style on the wagon I'd restored. I rebuilt what I had. Easy enough.
I bought the choke cable at the local tractor...
|
Forum: Early V8 (1932-53)
05-27-2024, 11:34 AM
|
Replies: 9
Views: 484
Re: Ford intake with S
Typically, a raised letter, numeral, etc. signifies (IE) the manufacturer, date, mold ID. My guess in this case is this was produced outside of the Ford Motor CO. as a service replacement part....
|
Forum: Early V8 (1932-53)
05-27-2024, 10:41 AM
|
Replies: 12
Views: 710
|
Forum: Model A (1928-31)
05-26-2024, 04:36 PM
|
Replies: 4
Views: 202
|
Forum: Model A (1928-31)
05-26-2024, 02:38 PM
|
Replies: 4
Views: 202
light switch install
Hello men!
Might seem simple to you but I'm kinda a newbie to the Model a world so here goes...
The piece on the end of the horn rod (picture attached) ... gets installed at the 3 and 9 o'clock...
|
Forum: Early V8 (1932-53)
05-25-2024, 12:08 PM
|
Replies: 12
Views: 710
Re: What is this ?
FYI, The compression fitting is not only unsafe within the brake line, it's illegal.
|
Forum: Early V8 (1932-53)
05-25-2024, 10:09 AM
|
Replies: 13
Views: 618
|
Forum: Early V8 (1932-53)
05-25-2024, 09:14 AM
|
Replies: 10
Views: 371
Re: Tail light connectore
Yep. They will work but you will need to grind down the diameter a bit. As is, they will not fit the connector.
|
Forum: Early V8 (1932-53)
05-25-2024, 07:26 AM
|
Replies: 21
Views: 740
|
Forum: Early V8 (1932-53)
05-23-2024, 04:16 PM
|
Replies: 10
Views: 376
|
Forum: Early V8 (1932-53)
05-22-2024, 04:30 PM
|
Replies: 11
Views: 592
Re: Banjo rear end hub, axle bearings and seals
The reproductions have a sorted history of poor quality. The cages were not (are not?) hardened properly and rather quickly, the cage would fail and the bearings were free to go where they wanted....
|
Forum: Early V8 (1932-53)
05-22-2024, 08:47 AM
|
Replies: 4
Views: 316
Re: Clutch pedal return spring '40 passenger
Here are two photographs that should help you. Note the hole atop the brace for one end of the spring to attach to.
I believe if you zoom in on the other photograph, you'll be able to see how the...
|
Forum: Early V8 (1932-53)
05-21-2024, 07:03 PM
|
Replies: 13
Views: 618
Re: Rusted 1940 cab
Found one more. I think that's all I have of what you wanted. Hope it helps...
|
Forum: Early V8 (1932-53)
05-21-2024, 04:50 PM
|
Replies: 13
Views: 618
|
Forum: Early V8 (1932-53)
05-21-2024, 02:31 PM
|
Replies: 11
Views: 592
|
Forum: Early V8 (1932-53)
05-20-2024, 08:48 PM
|
Replies: 14
Views: 807
|
Forum: Early V8 (1932-53)
05-20-2024, 07:16 PM
|
Replies: 14
Views: 807
Re: 1932/36 Condenser replacement.
For my cars and those clients that allow me to do what I prefer, I too use the 32's.
I think the last time I bought them; they were about $28. A bargain considering the confidence a guy gets with...
|
Forum: Early V8 (1932-53)
05-20-2024, 02:15 PM
|
Replies: 7
Views: 630
|
Forum: Early V8 (1932-53)
05-18-2024, 01:39 PM
|
Replies: 14
Views: 807
Re: 1932/36 Condenser replacement.
I use a Hunt's Magneto condenser. I have used both the 28mfd and 32mfd units. GREAT reliability. With the coil you are using, solder the original "bracket end" on to the condenser and shove the...
|