|
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
![]() |
Thread Tools | Display Modes |
![]() |
#1 |
Senior Member
Join Date: Jan 2020
Location: SF Bay Area
Posts: 1,175
|
![]()
I'm about to tear into a Model A engine to check bearing clearances, and I have a vague recollection that some of the nuts (rod cap nuts?) are an oddball socket size - 19/32" or 21/32" sticks in my mind. Am I imagining things? If the size is 19/32" (0.5938"), will a 15 mm (0.5906") fit?
Thanks, all.
__________________
JayJay San Francisco Bay Area ------------------------ 1930 Murray Town Sedan 1931 Briggs S/W Town Sedan |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,379
|
![]()
The originals were 21/32. I bought one in 1/2 inch drive size from Sears (Craftsman) years ago. I see that various 21/32 sockets can be found on Amazon for 4-5 bucks.
|
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#3 |
Senior Member
Join Date: Jan 2020
Location: SF Bay Area
Posts: 1,175
|
![]()
Thanks, Ursus. I ordered a cheap one off Amazon, supposed to show up Wednesday.
__________________
JayJay San Francisco Bay Area ------------------------ 1930 Murray Town Sedan 1931 Briggs S/W Town Sedan Last edited by JayJay; 09-12-2023 at 10:54 AM. |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Aug 2021
Location: alberta canada
Posts: 585
|
![]()
try a metric size that fits nice.
OU
__________________
old ugly my old father-in-law told me. "listen close when people tell you how to do stuff they may know something. then do it the way you want." |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Jan 2020
Location: SF Bay Area
Posts: 1,175
|
![]()
I ran that to see if I could make it work. 21/32" is 16.669 mm. A 17mm might work, but I'd hate to have it slip while torqueing. For $4.32 I got the right one. Besides, don't we always need a good excuse for a new tool? Or even a poor excuse?
__________________
JayJay San Francisco Bay Area ------------------------ 1930 Murray Town Sedan 1931 Briggs S/W Town Sedan |
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,123
|
![]() Sponsored Links (Register now to hide all advertisements)
__________________
Alaskan A's Antique Auto Mushers of Alaska Model A Ford Club of America Model A Restorers Club Antique Automobile Club of America Mullins Owner's Club |
![]() |
![]() |
![]() |
#7 | |
Senior Member
Join Date: Jan 2020
Location: SF Bay Area
Posts: 1,175
|
![]() Quote:
Fast forward to about five years ago after my last metric restoration (1973 BMW motorcycle) when I decided to go back to my roots, and began poking around for my SAE tools that had not seen the light of day for 50 years. I found quite a few I'd forgotten I had, but have had to supplement those a bit with more. So far I've been able to avoid a second roll-around toolbox for metric tools but I suppose that day is coming sometime.
__________________
JayJay San Francisco Bay Area ------------------------ 1930 Murray Town Sedan 1931 Briggs S/W Town Sedan |
|
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Mar 2012
Location: Ohio
Posts: 2,040
|
![]()
When I took my 1928 apart to check bearing clearances (way back when) the mains were 4 point nuts. 9/16" These were the ones that were nuts inside the engine . The car still had the multi-disc clutch, that dipper tray that Ford only used a couple of months, and stuff like that.
|
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: May 2010
Location: Portland OR
Posts: 6,360
|
![]()
Rods are 30-35 FPT, so you are not really reefing on them.
![]()
__________________
I know the voices aren't real but damn they have some good ideas! ![]() |
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: Jan 2020
Location: SF Bay Area
Posts: 1,175
|
![]()
Well, all the discussion was for naught, but I do appreciate y'alls feedback. The rod nuts were a solid 5/8", not 19/32" or 21/32". And the main nuts were 3/4". Bolt heads on the mains are 9/16" square. I have lots of 5/8" and 3/4" sockets and wrenches. The engine is 0.040" overbore so perhaps the rods got replaced when the engine was rebuilt.
BTW, I found some cheap 11 mm bolt thread protectors on Amazon (they were like $5.50 for 20 of them) and these fit the 7/16" rod studs perfectly.
__________________
JayJay San Francisco Bay Area ------------------------ 1930 Murray Town Sedan 1931 Briggs S/W Town Sedan |
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|