|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-19-2022, 07:13 PM | #1 |
Senior Member
Join Date: Dec 2012
Location: Payette, ID
Posts: 942
|
Looking for an expert to ID these wire wheels
wire wheels.jpg
17"x 3" wide. 5 on 4 1/2 36 bent spoke. Five of them came with a bunch of stuff. I think the right person would love to get these. But I have no clue what they are off of |
09-19-2022, 07:59 PM | #2 | |
Senior Member
Join Date: May 2015
Posts: 8,519
|
Re: Looking for an expert to ID these wire wheels
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
Sponsored Links (Register now to hide all advertisements) |
|
09-19-2022, 08:14 PM | #3 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,612
|
Re: Looking for an expert to ID these wire wheels
I think they are Chevy. I have lots of wheels, show us a pic of the back so I can see the hub area
|
09-19-2022, 08:17 PM | #4 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: Looking for an expert to ID these wire wheels
Chrysler???
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
09-19-2022, 11:26 PM | #5 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,612
|
Re: Looking for an expert to ID these wire wheels
Chrysler products usually have real spokes with adjustable spokes
|
09-19-2022, 11:28 PM | #6 |
Senior Member
Join Date: May 2010
Posts: 2,528
|
Re: Looking for an expert to ID these wire wheels
Sponsored Links (Register now to hide all advertisements)
|
09-20-2022, 03:52 AM | #7 |
Senior Member
Join Date: Feb 2011
Location: NNNNNNNNJJJJJJJJJJ
Posts: 6,839
|
Re: Looking for an expert to ID these wire wheels
most likely Mopar- most chevy wires are 6 lug.........
|
09-20-2022, 09:19 AM | #8 |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,086
|
Re: Looking for an expert to ID these wire wheels
Dodge or Plymouth and probably 1933 0r 34.
|
09-20-2022, 09:21 AM | #9 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,612
|
Re: Looking for an expert to ID these wire wheels
Chevy standards are 5 lug. master series are 6 lug. Dodges I have are all real adjustable spokes, and also 5 on 5.5. - will fit a ford hub, so not dodge
Last edited by cas3; 09-20-2022 at 09:24 AM. Reason: add |
09-20-2022, 09:32 AM | #10 |
Senior Member
Join Date: May 2010
Location: Pacific Grove, CA
Posts: 1,212
|
Re: Looking for an expert to ID these wire wheels
Post them on the AACA general discussion
|
09-20-2022, 10:15 AM | #11 |
Senior Member
Join Date: Dec 2012
Location: Anchorage Alaska
Posts: 292
|
Re: Looking for an expert to ID these wire wheels
I have a pair of 16x4 and say Kesly Hayes on them with the 4.5 bolt pattern. I have looked for years and never found what they really go to. They fit everything I have with disc brakes, but would need a spacer to work on drums dew to the way the back spoke flange is made. These look just like mine!
|
09-20-2022, 09:45 PM | #12 |
Senior Member
Join Date: Jun 2010
Location: St Croix Falls WI
Posts: 2,080
|
Re: Looking for an expert to ID these wire wheels
Dad had a 33 Dodge PE 4D .
Had twin sidemounts so you could see the odd wheels real good. Sure look the same to me. |
09-21-2022, 11:11 AM | #13 |
Senior Member
Join Date: Dec 2012
Location: Anchorage Alaska
Posts: 292
|
Re: Looking for an expert to ID these wire wheels
Also I never found a hubcap that would fit them. I welded about a 1/8 ring to the center to adapt them down to use a Ford hubcap.
|
09-21-2022, 07:22 PM | #14 |
Senior Member
Join Date: Aug 2012
Location: Henrietta, New York
Posts: 118
|
Re: Looking for an expert to ID these wire wheels
qmdv, I'm not an expert, but I did fine one listing for your 17' X 3" spoke wheels; bolt pattern 5 X 4 1/2"...in the "Original Equipment Wheels and Parts catalog No. 141; page #23".
Plymouth: 1932-34 models pc, pf, pc... Wheel mfg. p/n m21253 ; Car mfg. p/n 601091
__________________
1 RAGGEDY RIDE |
09-21-2022, 07:44 PM | #15 |
Senior Member
Join Date: Jun 2010
Location: St Croix Falls WI
Posts: 2,080
|
Re: Looking for an expert to ID these wire wheels
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|