|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
06-13-2013, 03:39 PM | #21 |
Senior Member
|
Re: Almost done with restoration but shifting problem, and more.
|
06-13-2013, 04:03 PM | #22 | |
Senior Member
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,940
|
Re: Almost done with restoration but shifting problem, and more.
Quote:
__________________
Dave / Lincoln Nebraska |
|
Sponsored Links (Register now to hide all advertisements) |
|
06-13-2013, 04:33 PM | #23 |
Senior Member
Join Date: May 2010
Location: Asheville,NC
Posts: 3,104
|
Re: Almost done with restoration but shifting problem, and more.
One letter can change the whole context of a sentence. That changes EVERYTHING. You need to pull that transmission and see what is wrong. I still believe, operator error. If the transmission is working correctly and, the Model A tranny is so simple there is not much that can go wrong, I can shift it and not scrape gears any worse than anyone else using a good clutch. If it will shift through the gears when the engine is stopped and the car is standing still, I can shift it when it is running and moving and, so should you be able to.
__________________
http://www.model-a-ford-4bangers.com/ |
06-13-2013, 04:47 PM | #24 |
Senior Member
|
Re: Almost done with restoration but shifting problem, and more.
Just got home from work. Asked my boss today about it and i am gonna check the brakes. The car could be draging and thus slowing down between each gear not allowing the trans and engine to match.
|
06-13-2013, 04:52 PM | #25 |
Senior Member
|
Re: Almost done with restoration but shifting problem, and more.
I took it around the block just now before touching the brakes and i Revved the engine up a bit as i double clutch (as you do downshifting) and it shifted as it should. So that makes me feel checking for a dragging drum may be the solution. They grab with the slightest touch of the pedal and i have had a loud sound from the shoes when on the brakes.
|
06-13-2013, 05:52 PM | #26 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,742
|
Re: Almost done with restoration but shifting problem, and more.
Sponsored Links (Register now to hide all advertisements)
Terry |
06-13-2013, 06:18 PM | #27 |
Junior Member
Join Date: Aug 2010
Location: San Antonio, Texas
Posts: 21
|
Re: Almost done with restoration but shifting problem, and more.
It sounds like the gear oil weight. Too heavy and it slows down the gears too quickly - which is why when you rev it, it shifts normally. Also, you stated during one run, it shifted better when it warmed up - the oil will thin as it warms up and let it shift easier.
I had a DOGde Dakota that did the same thing. When I changed to a lighter weight oil, it shifted normally. Gerry |
06-13-2013, 07:49 PM | #28 |
Senior Member
Join Date: Aug 2012
Location: Central NJ
Posts: 239
|
Re: Almost done with restoration but shifting problem, and more.
one of the first things I did when I got my barn find home was pulling the head. The thing hadnt been on the road since the 50s so I figured it would be a good idea. I found the water passages all filled with mouse nests, i kid you not mouse nests. If i tried to run it, there is no way water would have been able to flow.
__________________
1931 Slant Windshield fordor |
06-14-2013, 01:12 PM | #29 |
Senior Member
Join Date: May 2010
Posts: 440
|
Re: Almost done with restoration but shifting problem, and more.
I had a similar clutch problem over 40 years ago when I did my 1st A. I pulled the transmission 3 times and couldn't get it to shift right w/o grinding. Terry Oberer, who some of you may remember, came and helped me figure out that the clutch disc wasn't freely sliding on the input shaft. We took a die grinder and dressed the spines on the input shaft a bit to make sure the disc would slide nicely...problem solved. So I agree with Tom's earlier comment to check that out.
Good luck. |
06-14-2013, 03:24 PM | #30 |
Senior Member
Join Date: Jul 2010
Location: Pennsylvania
Posts: 1,117
|
Re: Almost done with restoration but shifting problem, and more.
A couple years ago I replaced my repro chrome shift lever with a butler nickle replated original that I bought at Hershey. The ball at the end that engages the shift forks had been built up round with weld before it was plated. With the old repro, I was able to shift with no grinding. With the new restored original, I found at first that I had to be really precise with the motion of the shift lever, and I had to double clutch between every shift or else it there would be grinding. It might have been that the ball was built up too much. I didn't check the diameter before installing. Anyway, it's gotten better (or maybe I've gotten better) over time, and I don't have to double clutch up through the gears any longer. The ball may have worn in some these last couple years.
|
06-14-2013, 06:08 PM | #31 |
Senior Member
Join Date: May 2010
Location: Asheville,NC
Posts: 3,104
|
Re: Almost done with restoration but shifting problem, and more.
Gentlemen, as for the clutch disk sliding on the shaft. He said he can remove the inspection cover and the clutch plate stops in a couple of seconds. If the plate were stuck and not sliding, this would not happen and the disk would not stop. I agree with the brake problem although, I have never experienced this.
__________________
http://www.model-a-ford-4bangers.com/ |
|
|
Sponsored Links (Register now to hide all advertisements) |
|