|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-18-2013, 08:00 PM | #1 |
Member
Join Date: Jun 2012
Location: Alton Bay, NH
Posts: 58
|
Pain in the Rear Hub!
Does anyone have a step-by-step on rear hub removal? Never done it before and I need to replace a stud. I have the hub remover and loosened the brake adjuster but the linings seem to be hanging up and I dont want to force anything. You folks have been a tremendous help throughout.
|
02-18-2013, 08:56 PM | #2 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Pain in the Rear Hub!
Put the tranny in neutral and if you still can't turn the hub then you need to loosen the brake linings, or remove the brake rods. Have you loosened the axle nut and tried the puller yet? What style puller do you have?
|
Sponsored Links (Register now to hide all advertisements) |
|
02-19-2013, 01:21 AM | #3 |
Senior Member
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,566
|
Re: Pain in the Rear Hub!
Do you have a hub removing tool? Just asking...
Mike
__________________
1930 TownSedan (Briggs) 1957 Country Sedan |
02-19-2013, 07:18 AM | #4 |
Senior Member
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,936
|
Re: Pain in the Rear Hub!
If it's hanging up on the brake shoes make certain that you have the brakes adjusted as far away from the drums as possible. If that doesn't do the trick use a torch and gently heat the outer circumfrence of the drum. Just go round and round and round with the torch. It may take a while as your not trying to get the drum super hot but just warm enough to expand the drum and loosen any built up grease ridge the shoes might be hanging up on. You shouldn't have to get it so hot you damage any paint.
Dave
__________________
Dave / Lincoln Nebraska |
02-19-2013, 07:24 AM | #5 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Pain in the Rear Hub!
It could also be hanging up on the emergency brake shoes which is a separate set than the regular brake. try removing the the e -brake rods off the cross shaft which is easier than getting to the clevis pins at the rear..
|
02-19-2013, 05:56 PM | #6 |
Member
Join Date: Jun 2012
Location: Alton Bay, NH
Posts: 58
|
Re: Pain in the Rear Hub!
Sponsored Links (Register now to hide all advertisements)
|
02-19-2013, 06:56 PM | #7 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,821
|
Re: Pain in the Rear Hub!
Try turning the drum as you are pulling it.
Bob |
02-19-2013, 07:08 PM | #8 |
Senior Member
Join Date: May 2010
Posts: 4,179
|
Re: Pain in the Rear Hub!
How long ago were the rear brakes "fully" overhauled?
Reason for asking: 1. Because of having "old" grease, the petroleum liquid material in the grease leaks out & evaporates, thus leaving a "dry", hard caked residue all around the brake adjusting wedge "and" the brake adjusting shafts. 2. This dry caked residue fills the threads & makes the brake adjusting wedge not only harder to turn, but can pile up & jam the threads such that the brake adjusting wedge will not turn even with brute force. 3. If so, one gets a false impression that the brakes are fully retracted; but they are not. 4. If the adjustig wedge can be rotated, maybe try injecting Kroil or Liquid Wrench plus WD-40 into the back side of the backing plate at the rotating square lug; then "turn both ways & inject Kroil" repeatedly, several times, to try to soften this dry caked old grease. 5. After a while, you may be able to turn the wedge a few more revolutions in the counter-clockwise direction to fully retract the brake shoes. Worth a try prior to wrapping the brake drums with TNT & a blasting cap. |
02-19-2013, 07:52 PM | #9 |
Senior Member
Join Date: Dec 2012
Location: Enterprise, WV.
Posts: 460
|
Re: Pain in the Rear Hub!
On your brake wedge if you can't see the threads your not out all the way. Pb blastor works good , try rotating the wedge in and out.
|
02-19-2013, 07:56 PM | #10 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 7,068
|
Re: Pain in the Rear Hub!
If it has hydraulics be sure it doesn't have safety hubs.
Charlie Stephens |
|
|
Sponsored Links (Register now to hide all advertisements) |
|