|
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
![]() |
Thread Tools | Display Modes |
![]() |
#1 |
Senior Member
Join Date: May 2010
Location: Western PA
Posts: 118
|
![]()
A problem has developed when I come to a stop at a stop sign or red light. My engine stops unless I step on accelerator or pull down on hand throttle. I have set idle to a faster RPM, adjusted carburetor, checked timing with no positive results. I am open to suggestions, Thanks Ray.
|
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jun 2010
Location: Kamloops B.C.
Posts: 392
|
![]()
Check the float level
|
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#3 |
Senior Member
Join Date: May 2010
Posts: 330
|
![]()
If you have another carb, give that a try first and see if it changes the behavior at all. You mention that it will stay running if you goose the throttle, so the problem does not appear electrical in nature. So the remaining items are air and fuel.
I would not expect that airflow stops at the stop sign. that leaves fuel. Float issues are notoriously stubborn to sort out, so see if you can try a known good carb. Have you adjusted the float level? You might have an issue with the float. I have seen floats that have developed pinhole leaks sinking them and causing the level to be too high and flooding the carb on stop with too muich fukel for the airflow. |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: May 2010
Location: Camino, CA.
Posts: 3,086
|
![]()
Sounds to me like the carburetor throttle shaft is worn and is leaking air. The fix is to install bushings in the carb to eliminate the leak. Brattons sells the bushings and instructions.
|
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: May 2010
Location: Canterbury, New Zealand
Posts: 1,242
|
![]()
Why not take out the jets & give them a good 'blow'. That will probably solve the problem.
|
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
![]() Sponsored Links (Register now to hide all advertisements)
|
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: May 2010
Location: Western PA
Posts: 118
|
![]()
Weather appears to have no effect,engine just dies on deceleration.The only time it does this is on stops.Otherwise, it runs just great,starts great,idles great,good power,etc.
|
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: May 2010
Location: Ontario, Canada
Posts: 1,470
|
![]()
__________________
I know a lot of things; I just can't remember them all. 1928 CCPU 82-A 1931 Roadster 40-B Dlx (Canadian) |
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: May 2010
Location: Naperville, IL
Posts: 1,387
|
![]()
Richen the idle mixture. Gar Williams
|
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: May 2010
Location: Anaheim California
Posts: 552
|
![]()
When driving around town, stop & go driving, open the mixture valve a quarter turn or so. Return to previous setting when on the road.
Richard Anaheim CA |
![]() |
![]() |
![]() |
#11 |
Senior Member
Join Date: Oct 2010
Location: gordonville mo
Posts: 519
|
![]() |
![]() |
![]() |
![]() |
#12 |
Member
Join Date: May 2010
Location: Chief lake BC Canada
Posts: 60
|
![]()
I had the same problem. The low speed passage in my carb was plugged.
|
![]() |
![]() |
![]() |
#13 |
Senior Member
Join Date: May 2010
Location: Western PA
Posts: 118
|
![]()
I checked all areas of previous posts that were suggested and I still have the same problem, engine dies when stopping. The only solution that I have found is prior to stopping move hand throttle down a couple of notches.
|
![]() |
![]() |
![]() |
#14 |
Senior Member
Join Date: May 2010
Location: Ontario, Canada
Posts: 1,470
|
![]()
You have replaced the throttle shaft as Glenn in Camino suggested?
Futzing with the throttle lever or GAV when coming to a stop is annoying and can be prevented. Good luck.
__________________
I know a lot of things; I just can't remember them all. 1928 CCPU 82-A 1931 Roadster 40-B Dlx (Canadian) |
![]() |
![]() |
![]() |
#15 |
Senior Member
Join Date: Jun 2010
Location: Perry OH
Posts: 1,343
|
![]()
With every thing else being ok I have solved that problem by adjusting the float level with a kit / clear line out side of the carb. mounted to a drill press plate with the carb. level. Set the level at 5/8".
|
![]() |
![]() |
![]() |
#16 |
Senior Member
Join Date: Oct 2011
Location: Reynolds Sta. Ky.
Posts: 106
|
![]() ![]() Jim |
![]() |
![]() |
![]() |
#17 |
Senior Member
Join Date: Jun 2010
Location: (Old)Shasta (Redding) CA
Posts: 386
|
![]()
Also check the manifold is tight and has no vacumn leaks.
|
![]() |
![]() |
![]() |
#18 |
Member
Join Date: May 2010
Posts: 39
|
![]()
Ray
I had the same problem and found that my compensator jet was too small. I replaced it with the proper size and the problem was solved. If the jet is too small the secondary well is drawn down by the idle jet when de-accelerating and can't refill quickly enough to prevent stalling from a lean mixture. This problem is worse when decending a hill with a stop sign at the bottom because going down hill effectivily lowers the fuel level in the secondary well. |
![]() |
![]() |
![]() |
#19 |
Senior Member
Join Date: May 2010
Location: Torrington, CT
Posts: 121
|
![]()
I had the same problem and went through most of the above suggestions - zip, still did it. Then I changed plugs. I got a repo set of 3X for a good price and so installed them, nothing to do with the stalling problem, just changed to the 3X.
No more stalling at a stop??? ![]() |
![]() |
![]() |
![]() |
#20 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
![]()
Open= leaner. Mixture screw is "ass backwards" from some carboonators.
__________________
"THE ASSISTANT GURU OF STUFF" |
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|