|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-09-2024, 06:18 AM | #1 |
Junior Member
Join Date: Apr 2024
Posts: 5
|
Ballast resistor for 12V coil
I've upgraded my 37 to 12V, negative ground. I also had the stock coil rebuilt to 12V neg ground as well. I was told to use a 2-ohm ballast resistor with the coil, but I haven't been able to locate one. Any suggestions? thanks
|
05-09-2024, 09:42 AM | #2 |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,059
|
Re: Ballast resistor for 12V coil
Chevrolet used ballast resistors for years on their ignitions. You might check to see what the ohm readings are for those resistors.
|
Sponsored Links (Register now to hide all advertisements) |
|
05-09-2024, 11:32 AM | #3 |
Senior Member
Join Date: May 2010
Location: Capital of Corruption , NY
Posts: 816
|
Re: Ballast resistor for 12V coil
Here's 1.8 for Chevy. https://www.summitracing.com/parts/s...MGL4lwMGmq19UI
|
05-09-2024, 12:25 PM | #4 |
Senior Member
Join Date: Jun 2016
Location: Pahrump, NV
Posts: 383
|
Re: Ballast resistor for 12V coil
Don't forget the starter solenoid that has the tap to bypass the resister. I stuffed a 406 BBF in my '56 T-bird. The 312 started fine. Stuffed in the 406 and could not start it until I discovered the solenoid was junk.
The '49 has GM electronics so no problem. When I ran the Chrysler electronics bypassing the resistor was a must. |
05-09-2024, 04:44 PM | #5 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,483
|
Re: Ballast resistor for 12V coil
A 1.2 to 1.5 Ohm ballast resistor will work for a 1.5 Ohm primary type coil. A person can use a 3 Ohm primary type coil and not need a ballast for 12-volt conversion.
|
05-09-2024, 05:22 PM | #6 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,396
|
Re: Ballast resistor for 12V coil
Sponsored Links (Register now to hide all advertisements)
R=V/I Where "V" is voltage, "R" is resistance (ohms), and "I "is current (amps). 12/4=3 ohms 6/4=1.5 ohms Bypassing the ballast resistor for easier staring is not part of this equation. |
05-09-2024, 07:06 PM | #7 |
Senior Member
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,997
|
Re: Ballast resistor for 12V coil
57 and up to the 80's some where Fords used a ballast resistor that is easy to get. I don't know the spec's on it.
__________________
48 Ford Conv 56 Tbird 54 Ford Victoria |
05-09-2024, 07:08 PM | #8 |
Senior Member
Join Date: May 2010
Location: Midland Park, NJ
Posts: 3,997
|
Re: Ballast resistor for 12V coil
They do make a coil that has a built in resistor. Check with a parts store.
__________________
48 Ford Conv 56 Tbird 54 Ford Victoria |
05-10-2024, 08:40 AM | #9 |
Junior Member
Join Date: Apr 2024
Posts: 5
|
Re: Ballast resistor for 12V coil
thanks. I'm planning on staying with the original/restored coil. I'm going with the 1.8 ohm Chevy resistor. I found plenty of 1.5 Ohm resistors on Amazon. Skip recommended 2 ohms so hopefully the 1.8 is sufficient.
|
05-10-2024, 10:59 AM | #10 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,483
|
Re: Ballast resistor for 12V coil
The built in resistor is a misnomer that I see a lot. It just has more resistance in the primary coil. The higher resistance primary makes more heat but modern internal insulation is a specific epoxy compound that can take the heat better than the old tar that they used to fill them with.
|
05-10-2024, 11:57 AM | #11 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,396
|
Re: Ballast resistor for 12V coil
It should be pretty simple. Just find the resistance of your coil in (ohms) as well as the resistance of the actual resistor. Add them together and run them through a version of the formula I posted above (I=V/R) to get the amperage you are putting through your points. If it is much more than 4 amps, your points will wear (burn) faster; lower, and you will not be getting the maximum potential from the ignition system. Actually, anything close to 4 amps should work fine.
|
05-10-2024, 01:04 PM | #12 |
Senior Member
Join Date: Jan 2019
Location: Chicago
Posts: 744
|
Re: Ballast resistor for 12V coil
|
05-10-2024, 09:53 PM | #13 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,396
|
Re: Ballast resistor for 12V coil
I agree with Jay (above). In thinking this over today, I would think it would be more accurate to use the actual voltages typically present in properly functioning automotive electrical systems (6.3 volts and 12.6 volts). I don't think it makes a lot of difference.
|
05-11-2024, 08:18 AM | #14 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,483
|
Re: Ballast resistor for 12V coil
Most 12-volt systems are regulated to 13.5 to 14-volts when the alternator or generator is in function. A 6-volt system should run at around 7.1 to 7.2-Volts.
|
05-11-2024, 11:34 AM | #15 |
Senior Member
Join Date: Jan 2019
Location: Chicago
Posts: 744
|
Re: Ballast resistor for 12V coil
Yes. And that normal variation in the applied voltage has a significant effect on everything downstream. Bigger effect than a few tenths of an ohm in the resistor. But everything downstream is used to it, can handle it. No microprocessors that would get all upset by small variations.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|