|
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
![]() |
Thread Tools | Display Modes |
![]() |
#21 |
Member
Join Date: Sep 2023
Location: Pittsburgh PA
Posts: 30
|
![]()
Its 223 6 cylinder
|
![]() |
![]() |
![]() |
#22 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,590
|
![]()
I can't find a decent photo. If you have a combination pump. the pump itself is on the PS of the engine and the intake manifold on the DS of the engine. The plumbing is complicated.
If no one here comes up with a photo, I will go down to my 'COBWEB CORNER' and look through the 1955 WSM. |
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#23 |
Member
Join Date: Sep 2023
Location: Pittsburgh PA
Posts: 30
|
![]()
Thanks for your help
|
![]() |
![]() |
![]() |
#24 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,590
|
![]()
Ain't no problem as I learn also ...
![]() |
![]() |
![]() |
![]() |
#25 |
Member
Join Date: Sep 2023
Location: Pittsburgh PA
Posts: 30
|
![]()
On hooking up the fuel pump vacuum lines if I go from the line to the intake and the other to the wiper it should work?
|
![]() |
![]() |
![]() |
#26 | |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,590
|
![]() Sponsored Links (Register now to hide all advertisements)
Quote:
I was trying to find a good photo but cannot. I still need to check the WSM to see if there is a good install ILL ... The will be four steel lines - FUEL LINE - MANIFOLD VACUUM SOURCE LINE - VACUUM MOTOR LINE TO MOTOR - LOAD-O-MATIC LINE FROM CAR TO DIST - See if these photos show large enough - ADDENDUM - Well, I have some old photos of the system but for some reason this system will not upload them.
__________________
*****
- WANNA SEE A GOOD CAR WRECK? - https://www.youtube.com/watch?v=5oO226PgSkg KULTULZ - HAS MOVED ON TO THE HAPPY PROVING GROUNDS Last edited by KULTULZ; 11-05-2023 at 11:38 AM. Reason: THE USUAL |
|
![]() |
![]() |
![]() |
#27 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,590
|
![]()
__________________
*****
- WANNA SEE A GOOD CAR WRECK? - https://www.youtube.com/watch?v=5oO226PgSkg KULTULZ - HAS MOVED ON TO THE HAPPY PROVING GROUNDS |
![]() |
![]() |
![]() |
#28 |
Member
Join Date: Sep 2023
Location: Pittsburgh PA
Posts: 30
|
![]()
Thanks for the pictures It all makes sense now
|
![]() |
![]() |
![]() |
#29 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,590
|
![]()
I was hoping to do better. The MPC doesn't show a detailed engineering drawing of the install(s). I haven't opened the WSM yet but also doubt it goes into detail.
It is the same design just split because FORD put the components on differing sides of the engine for the I-223 SERIES,
__________________
*****
- WANNA SEE A GOOD CAR WRECK? - https://www.youtube.com/watch?v=5oO226PgSkg KULTULZ - HAS MOVED ON TO THE HAPPY PROVING GROUNDS |
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|