|
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
![]() |
Thread Tools | Display Modes |
![]() |
#21 | |
Senior Member
Join Date: Aug 2012
Location: IN A GALAXIE FAR, FAR AWAY
Posts: 7,386
|
![]() Quote:
![]()
__________________
***** "Last Sunday, I caught him makin' eyes at Idell Bushey durin' preachin'. And I know what they do up there in the hills when they say they're possum huntin'. They're just sittin' around the campfire, drinkin' hard cider, hittin' each other on the shoulder and hollerin' 'flinch!'." ― Charlene Darling (Daughter of Briscoe Darling) |
|
![]() |
![]() |
![]() |
#22 |
Senior Member
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,794
|
![]()
I think it will work. I don't think the angle is severe enough to not be able to compensate by changing the float level slightly. The bowls face the rear on the tri power setups, so that means on the main jet side of the bowl the fuel level will be slightly lower. I'll compensate by setting the floats slightly higher.
I've done it before without issues. Sal |
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#23 |
Senior Member
Join Date: Oct 2014
Location: NE Iowa
Posts: 1,767
|
![]()
I guess that would be right. We don't adjust float bowls driving up or down hills, never thought of it that way.
|
![]() |
![]() |
![]() |
#24 |
Senior Member
Join Date: Aug 2012
Location: IN A GALAXIE FAR, FAR AWAY
Posts: 7,386
|
![]()
Not that it is any of my business, what did the owner say about this?
Center pivot floats addresses this problem (driving change in angles) not the carb being initially installed at the wrong angle.
__________________
***** "Last Sunday, I caught him makin' eyes at Idell Bushey durin' preachin'. And I know what they do up there in the hills when they say they're possum huntin'. They're just sittin' around the campfire, drinkin' hard cider, hittin' each other on the shoulder and hollerin' 'flinch!'." ― Charlene Darling (Daughter of Briscoe Darling) |
![]() |
![]() |
![]() |
#25 |
Senior Member
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,794
|
![]()
I gave the owner a link to this post, and he wants to go forward with it.
I've done some carb angle testing on flow boxes when I worked at the Zenith Carburetor engineering lab in Detroit, and have done comlete carb flows at severe angles, and feel pretty confident this will work. I know from an appearance standpoint a lot of people will say no, but the ownwer is aware of this and has mocked it up on his Galaxie. Sal |
![]() |
![]() |
![]() |
#26 | |
Senior Member
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,794
|
![]() Sponsored Links (Register now to hide all advertisements)
Quote:
I sent you a personal message with a question. Not sure if you've seen it or not. Thanks, Sal |
|
![]() |
![]() |
![]() |
#27 |
Senior Member
Join Date: Feb 2011
Location: outside Omaha, NE
Posts: 281
|
![]()
Check your PMs to see if you got my response. If not, I may have a 'plan B' to work with.
__________________
Alan H. Tast AIA, LEED AP BD+C Technical Director/Past President-Editor-Publications Director, Vintage Thunderbird Club Int'l. (VTCI) http://www.vintagethunderbirdclub.net Author, "Thunderbird 1955-1966" & "Thunderbird 50 Years" 35+ year member, Crown Victoria Ass'n. |
![]() |
![]() |
![]() |
#28 |
Senior Member
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,794
|
![]() |
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|