|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
06-17-2022, 05:43 PM | #1 |
BANNED
Join Date: Jun 2010
Location: Utica, Ohio
Posts: 522
|
Edelbrock manifold
Can someone tell me the model no. or name of this manifold. Any opinions on the performance improvement? It runs very strong on the engine shown. It is a 276ci.
|
06-17-2022, 05:51 PM | #2 |
BANNED
Join Date: May 2010
Location: Wa.
Posts: 5,423
|
Re: Edelbrock manifold
Performance improvement, mediocre, compared to an SU359 on a 276.
|
Sponsored Links (Register now to hide all advertisements) |
|
06-17-2022, 06:17 PM | #3 |
Senior Member
Join Date: May 2010
Location: upstate SC
Posts: 2,986
|
Re: Edelbrock manifold
if you have to have a 2-3 intake it is a good set up with the two carbs balanced it runs good. at least it has a very good air cleaner!! not one of those restrictive round hat type.
|
06-17-2022, 07:21 PM | #4 |
BANNED
Join Date: Jun 2010
Location: Utica, Ohio
Posts: 522
|
Re: Edelbrock manifold
I had those little chrome pots on it. When I made and installed that big air cleaner I could tell a difference in performance. I think it's running a little lean so I'm going to change jet sizes.
|
06-18-2022, 08:02 AM | #5 |
Senior Member
Join Date: Feb 2011
Location: Buchanan, MI
Posts: 676
|
Re: Edelbrock manifold
The manifold is an Edelbrock regular for an 8BA.
|
06-18-2022, 08:36 AM | #6 |
BANNED
Join Date: May 2010
Posts: 3,019
|
Re: Edelbrock manifold
Sponsored Links (Register now to hide all advertisements)
an 8BA the gen or alternator remains in the stock location. On earlier motors an alternator fits just right so no offset bracket req'd. This intake or a close copy goes on most motors leaving my shop. Charlie ny |
06-18-2022, 10:19 AM | #7 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,901
|
Re: Edelbrock manifold
The intake manifold I like best for a preformance application is the Offy 1076 this "Super dual: has better orting and is apros 1" higher than the Edelbrock / The carb flanges are large enough the bored out for the 2GC carb or the Holly big bor truck carb( can't find any information on this carb) I got it from Charley Price and used them on the Hydro engines. However I used 2G carbs on the Beville engine. Is there a better setup? Probably, but this is a cost effective Method that works very well. For street use the 1 1/16 Holly work very well.
Gramps |
06-18-2022, 05:44 PM | #8 |
BANNED
Join Date: Jun 2010
Location: Utica, Ohio
Posts: 522
|
Re: Edelbrock manifold
Thank you all. Guess it won't make 200 HP!
|
06-18-2022, 06:52 PM | #9 |
BANNED
Join Date: May 2010
Location: Wa.
Posts: 5,423
|
Re: Edelbrock manifold
|
06-18-2022, 07:17 PM | #10 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,423
|
Re: Edelbrock manifold
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|