The Ford Barn

sprint29 · 03-07-2022, 11:19 AM

Good morning.
I was wondering where a guy can get the drawings for the front inner fender wells on a 36 pickup?
Mine are butchered up some and I'd like to see what they are suppose to look like.
Thanks
Mark

CA Victoria · 03-07-2022, 11:22 AM

Check here on page 3 post #45
https://www.fordbarn.com/forum/showthread.php?t=298830

Sorry, I mis read your post.
Rather than make your own, (the top edge is a bit complex) look for a set off of a 1 1/2t truck. You will need to fuss with the bottoms a bit but the tops are spot on. A paper pattern can be used to determine the cut edge on the bottom

sprint29 · 03-07-2022, 03:05 PM

The top edge on these things is in good shape. They cut parts of the bottom half to make room for after market shocks. Do you know if both sides are the same except for a right and left?

VeryTangled · 03-07-2022, 04:53 PM

Quote:

Originally Posted by sprint29

I was wondering where a guy can get the drawings for the front inner fender wells on a 36 pickup? Thanks Mark

Hi Everyone. Mark, if they are anywhere, the drawings are at the Benson Ford Research Center at The Henry Ford in Dearborn. This place has an amazing collection and 'librarians' that know how to find things.

The link, if you go down about 1/2 way, has a Services area. In there is a place where you can ask a research center expert, and another place where you can get fee-based remote research.

Maybe this helps.

https://www.thehenryford.org/collections-and-research/

CA Victoria · 03-07-2022, 07:23 PM

These aren’t the best but you are correct about being the same shape for R & L.
Send a PM If you need a tracing.

Don Rogers · 03-08-2022, 01:01 AM

Sponsored Links (Register now to hide all advertisements)

Here are some pictures of inner fender panels that might help.

sprint29 · 03-08-2022, 09:46 AM

Thanks guys,
All the info and pictures help greatly. I can fix mine with a little sheet metal work. Just wasn't sure exactly what they looked like. When I got this truck it had an old Doge hemi in it. They had to cut the chassis, firewall, floorboard and fender wells to get this thing to fit. I'm trying to get it back to original.

CA Victoria · 03-08-2022, 10:47 AM

Congrats, good to see another one saved

03-07-2022, 11:19 AM	#1
sprint29 Member Join Date: Oct 2015 Location: springfield,mo Posts: 76	36 pickup inner fender well drawings Good morning. I was wondering where a guy can get the drawings for the front inner fender wells on a 36 pickup? Mine are butchered up some and I'd like to see what they are suppose to look like. Thanks Mark

03-07-2022, 11:22 AM	#2
CA Victoria Senior Member Join Date: Feb 2011 Posts: 2,216	Re: 36 pickup inner fender well drawings Check here on page 3 post #45 https://www.fordbarn.com/forum/showthread.php?t=298830 Sorry, I mis read your post. Rather than make your own, (the top edge is a bit complex) look for a set off of a 1 1/2t truck. You will need to fuss with the bottoms a bit but the tops are spot on. A paper pattern can be used to determine the cut edge on the bottom __________________ Tim Downtown, Ca Last edited by CA Victoria; 03-07-2022 at 11:28 AM.

03-07-2022, 03:05 PM	#3
sprint29 Member Join Date: Oct 2015 Location: springfield,mo Posts: 76	Re: 36 pickup inner fender well drawings The top edge on these things is in good shape. They cut parts of the bottom half to make room for after market shocks. Do you know if both sides are the same except for a right and left?

03-08-2022, 09:46 AM	#7
sprint29 Member Join Date: Oct 2015 Location: springfield,mo Posts: 76	Re: 36 pickup inner fender well drawings Thanks guys, All the info and pictures help greatly. I can fix mine with a little sheet metal work. Just wasn't sure exactly what they looked like. When I got this truck it had an old Doge hemi in it. They had to cut the chassis, firewall, floorboard and fender wells to get this thing to fit. I'm trying to get it back to original.