|
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
![]() |
Thread Tools | Display Modes |
![]() |
#1 |
Senior Member
Join Date: May 2010
Location: Charlestown,R.I.
Posts: 465
|
![]()
Is there a way to drill on carpet instead of cutting out small piece where hole will be for safety belts. Ford came with holes because it was optional but you still have to make hole in carpet for bolt to go through.
|
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 11,027
|
![]()
Here's a video that shows how to do it. Really easy.
https://www.youtube.com/watch?v=dpufNiXvQgU |
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#3 |
Member
Join Date: Apr 2019
Location: Pacific NW
Posts: 30
|
![]()
I use a cheap soldering iron to melt any necessary holes through carpet- no chance of creating a run, prevents the screws/bolts from pulling the yarn, too.
|
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,518
|
![]()
I use a gasket hole cutter but the hole has to be marked with chalk and use a wood block on a hard surface to back it up. Sharpened steel tubing of the proper diameter will also work as a cutter.
|
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: May 2010
Location: Huntsville Al
Posts: 1,528
|
![]()
I do the same as datac. I use a soldering iron. It seals the thread while it makes the hole.
__________________
Matt 24:36-41 |
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: May 2014
Location: Tulsa, Oklahoma
Posts: 151
|
![]() Sponsored Links (Register now to hide all advertisements)
Last edited by y'sguy; 05-06-2019 at 09:23 PM. Reason: just had to type…one…more …thing… |
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: May 2010
Location: Granite City, Illinois
Posts: 3,008
|
![]()
What I have done in the past for #6 - #8 finishing screws thru the carpet, is to go underneath first and poke a needle thru the carpet in the center of the hole. Then get a Prestolite torch and heat up the tip of a 16D nail (while holding the nail with a pair of pliers, then push the needle thru the carpet on the topside and melt the nylon carpeting with the nail-head.
But for larger holes, (I suspect you might need a 1/4" or 5/16" hole for the seat belt), you could use same procedure as above except use a tapered center-punch instead of a 16D nail. |
![]() |
![]() |
![]() |
#8 |
Member
Join Date: Apr 2019
Location: Pacific NW
Posts: 30
|
![]() |
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: May 2010
Posts: 875
|
![]()
I use 1/4 " p1pe and heat it with torch and it will melt through and leave a smooth neat hole.
|
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: Jul 2012
Location: Orange Park, Fl
Posts: 406
|
![]()
Slick and easy solution to an age-old problem. Thanks for the tip.
|
![]() |
![]() |
![]() |
#11 |
Senior Member
Join Date: Nov 2012
Location: Central Texas
Posts: 156
|
![]()
A tapered punch and a hammer works for me. Just drive the punch through the carpet and floor pan until the desired hole size in the floor pan is obtained. Ted Eaton.
|
![]() |
![]() |
![]() |
#12 |
Member
Join Date: Feb 2017
Posts: 44
|
![]()
I like the soldering iron idea because it will make a neat hole.
|
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|