The Ford Barn

carolina-bob · 11-20-2015, 05:41 PM

Can someone point me in the right direction to find the installed lenghts of the head studs for a 35 with aluminum heads. I know I've seen it somewhere but over the years, sometimes I forgets.

Thanks

adileo · 11-20-2015, 07:24 PM

Google Roy Nacewicz enterprise can help you

russcc · 11-21-2015, 08:15 PM

Check the Green bible. There are specific studs and washers for Alm heads.
40-6065 2.34" '32-36
40-6066 2.90" '32-36
40-4067 3.59" '32-36

351428 washer '33-37, use w/alm heads

Pages 231, 232 in the bible.

JSeery · 11-21-2015, 09:27 PM

Quote:

Originally Posted by russcc

Check the Green bible. There are specific studs and washers for Alm heads.
40-6065 2.34" '32-36
40-6066 2.90" '32-36
40-4067 3.59" '32-36

351428 washer '33-37, use w/alm heads

Pages 231, 232 in the bible.

If we are talking OEM alum heads, which it sounds like he is.

carolina-bob · 11-22-2015, 08:22 AM

Yes they are OEM heads. I talked with Roy N and it looks like its going to be a trial and error install.

carolina-bob · 11-22-2015, 03:07 PM

Sponsored Links (Register now to hide all advertisements)

Installing the studs is not the problem as I have done them before. Somewhere I would think there is an established/recommended dimension from the block deck to the upper end of the studs for each of the three length studs used on the 35 after installation. Taking a couple of measurements on studs that look like they are at the right length- the long stud is about 2-15/16 and the intermediate studs are about 2- 1/4 from block to top of stud. I haven't measured the short studs yet but will later today. I plan on using these dims to set the remaining studs. Thanks Bob

JSeery · 11-22-2015, 03:36 PM

So are we saying the Green Book values (lengths) are not correct? I don't know, just asking the question.

11-20-2015, 05:41 PM	#1
carolina-bob Member Join Date: May 2010 Location: Greenville NC Posts: 83	Head studs Can someone point me in the right direction to find the installed lenghts of the head studs for a 35 with aluminum heads. I know I've seen it somewhere but over the years, sometimes I forgets. Thanks

11-20-2015, 07:24 PM	#2
adileo Senior Member Join Date: Jun 2014 Location: New Jersey Posts: 1,772	Re: Head studs Google Roy Nacewicz enterprise can help you

11-21-2015, 08:15 PM	#3
russcc Senior Member Join Date: May 2010 Posts: 2,871	Re: Head studs Check the Green bible. There are specific studs and washers for Alm heads. 40-6065 2.34" '32-36 40-6066 2.90" '32-36 40-4067 3.59" '32-36 351428 washer '33-37, use w/alm heads Pages 231, 232 in the bible.

11-22-2015, 08:22 AM	#5
carolina-bob Member Join Date: May 2010 Location: Greenville NC Posts: 83	Re: Head studs Yes they are OEM heads. I talked with Roy N and it looks like its going to be a trial and error install.

11-22-2015, 03:07 PM	#6
carolina-bob Member Join Date: May 2010 Location: Greenville NC Posts: 83	Re: Head studs Sponsored Links (Register now to hide all advertisements) Installing the studs is not the problem as I have done them before. Somewhere I would think there is an established/recommended dimension from the block deck to the upper end of the studs for each of the three length studs used on the 35 after installation. Taking a couple of measurements on studs that look like they are at the right length- the long stud is about 2-15/16 and the intermediate studs are about 2- 1/4 from block to top of stud. I haven't measured the short studs yet but will later today. I plan on using these dims to set the remaining studs. Thanks Bob

11-22-2015, 03:36 PM	#7
JSeery Member Emeritus Join Date: Nov 2012 Location: Wichita KS Posts: 16,132	Re: Head studs So are we saying the Green Book values (lengths) are not correct? I don't know, just asking the question.