The Ford Barn

1931 flamingo · 02-05-2012, 09:57 AM

Trekked up to Hazardville, CT this am for the monthly swap meet. Nice to run into Barry B. and Ken, CT and BS for a while. Thanks guys.
Paul in CT

Dennis/CT · 02-05-2012, 11:18 AM

I here alot about this swap meet but I don't see it advertised.When and where is it held each month? Thanks, Dennis/CT

ken ct · 02-05-2012, 11:54 AM

You will only see it advertized on here. 1st sunday of the mth. Its small,very small about a dozen vendors,mostly model A and V8 stuff and tools [not jap stuff] usa made scockets ,wrenches screwdrivers etc etc, [1 vendor] nice little swap in the winter mths. Good seeing you again 31 flamingo take care fellas and see you nxt mth. ken ct. Oh you tooo Barry lol.

Roadster62 · 02-05-2012, 12:41 PM

Add me to the list of people that haven't been to it yet, maybe next month if someone posts a reminder.

Barry B./ Ma. · 02-05-2012, 02:04 PM

Put it on your calendar, it will be Mar.4 and I think that will be it for this year. Saw 2 nice 28/29 ccpickups drive in when we were leaving. Get there early, there were people there today before 7AM. Nice to chat with you too Paul (Flamingo) and Ken ct.
PS bought a nice clutch disc and pressure plate with only 1200 miles from Lenny. Good guy to deal with, usually rebuilds carbs and distributors.

Dennis/CT · 02-05-2012, 05:03 PM

Sponsored Links (Register now to hide all advertisements)

How about an address or directions?

spdway1 · 02-05-2012, 05:14 PM

" Saw 2 nice 28/29 ccpickups drive in when we were leaving. "

The NEXT Generation!

ken ct · 02-05-2012, 05:26 PM

Quote:

Originally Posted by Dennis/CT

How about an address or directions?

North on I-91 past the Airport,get off at exit for rt 190 E go about 3 mi.on it to a cross street with a traffic lite,take a rt. and proceed down that rd as you go down the hill you will see and old red barn on the rt thats it.Less than a mile from the lite. Ha ha the meet is on my birthday.Gotta be my lucky day. ken ct.

cayager · 02-05-2012, 06:37 PM

Quote:

Originally Posted by spdway1

" Saw 2 nice 28/29 ccpickups drive in when we were leaving. "

The NEXT Generation!

i saw those too. 1 guy was doing burnouts in the street

spdway1 · 02-05-2012, 08:30 PM

They were at Tractor Supply too!

1931 flamingo · 02-05-2012, 08:32 PM

Dennis/ CT: It's actually in hazardville, take the way Ken CT said but after you get onto 190 it's about 5 miles, at traffic light there's a Whole Donut shop on the left just before you're going to turn right. Bring some Jimmie's dogs and clams with you. haha
Paul in CT

02-05-2012, 09:57 AM	#1
1931 flamingo Senior Member Join Date: May 2010 Location: new britain,ct 06052 Posts: 9,428	Powder Mill Trekked up to Hazardville, CT this am for the monthly swap meet. Nice to run into Barry B. and Ken, CT and BS for a while. Thanks guys. Paul in CT

02-05-2012, 11:18 AM	#2
Dennis/CT Senior Member Join Date: May 2010 Location: West Haven, CT Posts: 143	Re: Powder Mill I here alot about this swap meet but I don't see it advertised.When and where is it held each month? Thanks, Dennis/CT

02-05-2012, 11:54 AM	#3
ken ct BANNED Join Date: May 2010 Location: stratford,ct Posts: 5,971	Re: Powder Mill You will only see it advertized on here. 1st sunday of the mth. Its small,very small about a dozen vendors,mostly model A and V8 stuff and tools [not jap stuff] usa made scockets ,wrenches screwdrivers etc etc, [1 vendor] nice little swap in the winter mths. Good seeing you again 31 flamingo take care fellas and see you nxt mth. ken ct. Oh you tooo Barry lol.

02-05-2012, 12:41 PM	#4
Roadster62 Senior Member Join Date: May 2010 Location: Ridgefield, Ct Posts: 3,449	Re: Powder Mill Add me to the list of people that haven't been to it yet, maybe next month if someone posts a reminder. __________________ They don't have to run to be enjoyed. I'm here to enjoy the hobby, and enjoy the cars no matter what they look like. Most of the worlds problems are electrical.

02-05-2012, 02:04 PM	#5
Barry B./ Ma. Senior Member Join Date: May 2010 Location: Southbridge, Ma. Posts: 1,614	Re: Powder Mill Put it on your calendar, it will be Mar.4 and I think that will be it for this year. Saw 2 nice 28/29 ccpickups drive in when we were leaving. Get there early, there were people there today before 7AM. Nice to chat with you too Paul (Flamingo) and Ken ct. PS bought a nice clutch disc and pressure plate with only 1200 miles from Lenny. Good guy to deal with, usually rebuilds carbs and distributors.

02-05-2012, 05:03 PM	#6
Dennis/CT Senior Member Join Date: May 2010 Location: West Haven, CT Posts: 143	Re: Powder Mill Sponsored Links (Register now to hide all advertisements) How about an address or directions?

02-05-2012, 05:14 PM	#7
spdway1 Senior Member Join Date: Feb 2011 Location: Chicopee, MA Posts: 1,493	Re: Powder Mill " Saw 2 nice 28/29 ccpickups drive in when we were leaving. " The NEXT Generation!

02-05-2012, 08:30 PM	#10
spdway1 Senior Member Join Date: Feb 2011 Location: Chicopee, MA Posts: 1,493	Re: Powder Mill They were at Tractor Supply too!

02-05-2012, 08:32 PM	#11
1931 flamingo Senior Member Join Date: May 2010 Location: new britain,ct 06052 Posts: 9,428	Re: Powder Mill Dennis/ CT: It's actually in hazardville, take the way Ken CT said but after you get onto 190 it's about 5 miles, at traffic light there's a Whole Donut shop on the left just before you're going to turn right. Bring some Jimmie's dogs and clams with you. haha Paul in CT Last edited by 1931 flamingo; 02-05-2012 at 08:33 PM. Reason: add the dogs