The Ford Barn

Kohnke Rebabbitting · 06-02-2018, 02:20 PM

There are some Machine Videos of this machine Shop doing a Model A, or B, Ford.

Comments Please!

https://www.youtube.com/watch?v=rDD78ADKP_w

Brentwood Bob · 06-02-2018, 02:50 PM

Crank grinding one was revitting.
Saw a recent build and owner ordered a second right away.
Said it ran like a Swiss watch. However, when towed on a dolly in gear the first engine took out #1 cylinder.

4port · 06-02-2018, 03:33 PM

Where is the head and block resurfacer. Where is the boring bar, who chases a cylinder bore on mill. Needs sleeve and valve seat installed. Forget about boring oversize, let's just hone it dry, it cuts faster. We dont own a cylinder honing machine, or boring bar. It's a blue printed "race block". I'm sure I saw a positive pressure clean room for assembly, didn't you? You saw in on the Internet, it must be true.

F.M. · 06-02-2018, 04:58 PM

Better off using a file !!

Mark DeRoseau · 06-02-2018, 06:20 PM

Bet they used the scale to tram the head in as well, before they put their last good insert in that bear claw. Actually don't think there was one good insert in that thing.....

Brentwood Bob · 06-02-2018, 11:17 PM

Sponsored Links (Register now to hide all advertisements)

Quote:

Originally Posted by Brentwood Bob

Crank grinding one was revitting.
Saw a recent build and owner ordered a second right away.
Said it ran like a Swiss watch. However, when towed on a dolly in gear the first engine took out #1 cylinder.

Well maybe I should watch the video first, assumed it was of your video.

Pete · 06-03-2018, 01:53 PM

Mickey Mouse was a piker compared to those guys.

Benson · 06-03-2018, 03:46 PM

...

06-02-2018, 02:50 PM	#2
Brentwood Bob Senior Member Join Date: May 2010 Location: brentwood, ca Posts: 4,420	Re: Machine Videos Crank grinding one was revitting. Saw a recent build and owner ordered a second right away. Said it ran like a Swiss watch. However, when towed on a dolly in gear the first engine took out #1 cylinder.

06-02-2018, 03:33 PM	#3
4port Senior Member Join Date: May 2010 Location: Dallas TX Posts: 112	Re: Machine Videos Where is the head and block resurfacer. Where is the boring bar, who chases a cylinder bore on mill. Needs sleeve and valve seat installed. Forget about boring oversize, let's just hone it dry, it cuts faster. We dont own a cylinder honing machine, or boring bar. It's a blue printed "race block". I'm sure I saw a positive pressure clean room for assembly, didn't you? You saw in on the Internet, it must be true. __________________ Remember when flying low inverted, down is up, and up can be expensive.

06-02-2018, 04:58 PM	#4
F.M. BANNED Join Date: Sep 2017 Posts: 385	Re: Machine Videos Better off using a file !!

06-02-2018, 06:20 PM	#5
Mark DeRoseau Member Join Date: Aug 2014 Location: Grand Rapids MI Posts: 45	Re: Machine Videos Bet they used the scale to tram the head in as well, before they put their last good insert in that bear claw. Actually don't think there was one good insert in that thing.....

06-03-2018, 01:53 PM	#7
Pete BANNED Join Date: May 2010 Location: Wa. Posts: 5,423	Re: Machine Videos Mickey Mouse was a piker compared to those guys.

06-02-2018, 02:20 PM	#1
Kohnke Rebabbitting Senior Member Join Date: May 2010 Location: 60615,330th Ave.,Clare, Iowa, 50524 Posts: 1,457	Machine Videos There are some Machine Videos of this machine Shop doing a Model A, or B, Ford. Comments Please! https://www.youtube.com/watch?v=rDD78ADKP_w

06-03-2018, 03:46 PM	#8
Benson Senior Member Join Date: May 2010 Location: Cen~Col - Central Highlands Posts: 2,757	Re: Machine Videos ... Last edited by Benson; 06-03-2018 at 06:41 PM.