Looking for this DIFFICULT to locate part - do you have it?

[Hot Rod Reverend]

1955 Ford Fairlane Club Sedan - need the "L" shaped stud (upside down L anyway) that allows the vent window to pivot. These things are known to rot out. Every last vent window assembly in my stash - all were rotted away to just about nothing.

Passenger side or Driver side, either will fit. See the diagram.

Let me know if you have one or where I could purchase one off the shelf.

Thanks fellas

[KULTULZ]

Below is a blow-up of your ILL.

Hopefully it will show large enough to view properly. The part you are describing, is there a BASIC PN with an arrow pointing to it?

Your car is a 1955 FAIRLANE TUDOR CLUB SEDAN (70C)?

[raceron1120]

I looked too; can't find that it was serviced separately but only as part of the frame. Not sure of any aftermarket sources for it.

Carpenter has a few listed but for pickups or Broncos. Not sure it they would work or could be modified. Here's one:

https://www.dennis-carpenter.com/tru...-pivot-assy-lh

[56sedandelivery]

Went and looked at my stash and every frame I have does not have that part on it. I guess I cannibalized them to make up the two good ones.

[1930artdeco]

I am assuming you are looking for the vertical pin that the window rides on. There are few swap meets coming up next month and I can look for you. It may mean getting the whole window if you are good with that. When they get close I can PM you my number so if I find one I can call you.

Mike

[50fordcoupeman]

Sponsored Links (Register now to hide all advertisements)

My avatar had the same part issue. I was able to get one from Shoebox Central-405 259 9222. From the ilustration it appears to be identical. Good luck!

[Hot Rod Reverend]

WOW!

Ask and ye shall receive... you guys are on this, much appreciated. My passenger side vent window is "just a floppin' in the wind" so I need to replace this broken stud/bracket to make Mama happy.

Yes, a 70C - 1955 Fairlane Tudor Club Sedan. There is no arrow pointing as far as I can see. I will have to check my other manual to see if I can locate an actual part number.

I will contact Shoebox

[paul2748]

At one time Restoration Specialties (PA) had some of these. Try them

[Gene F]

Is that a part that is likely to be re-engineered from year-to-year?

[50fordcoupeman]

Hotrod..............Mine was actually for the rear quarter window but I think they are the same L piece. Careful with glass as I broke mine putting the glass back into the frame! AAArgh!!

[KULTULZ]

If it is the wing glass frame pivot pin you are after, it was offered only as an assembly (frame incl glass) from FOMOCO -

B5A 7021406-A (RH)
B5A 7021407-A (LH)

Be careful here if searching EvilBay as there is one offered but the seller has the PN listed incorrectly. His has a BASIC PN (shown) 7621407 (LS) which is for a HDTP or CONV.

We have your back REVEREND, and as for myself, the lightening strikes are getting closer ...

[56sedandelivery]

found this in my junk pile. You can have it for shipping and whatever you feel.

[KULTULZ]

... damn ...

[Hot Rod Reverend]

Originally Posted by 56sedandelivery

found this in my junk pile. You can have it for shipping and whatever you feel.

PM sent - thank you so much

[KULTULZ]

Originally Posted by 56sedandelivery

found this in my junk pile. You can have it for shipping and whatever you feel.

That was awful nice to do that ...

[Tbone]

I have vent Windows from 56 Mercury, look like the same. Let me know if still need

[Hot Rod Reverend]

I mailed 56sedandelivery a check today - should get there soon. Much appreciated!

And thank you guys for all the quick responses!