Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)
Reload this Page KR Wilson engine lifting bracket

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 04-23-2024, 04:58 AM   #1
BlueNotes
Senior Member
 
Join Date: May 2010
Location: Land of the Midnight Sun
Posts: 182
Default KR Wilson engine lifting bracket
I recently scored a repro KRW engine lifting bracket but the 2 knurled pins are missing. Can anyone advise the measures (or a simple drawing) for the pin so I can make them?
Attached Images
File Type: jpg KRW 6000.jpg (113.1 KB, 230 views)
BlueNotes is offline   Reply With Quote
Old 04-23-2024, 08:20 AM   #2
hop up
Senior Member
 
hop up's Avatar
 
Join Date: Jun 2010
Posts: 439
Default Re: KR Wilson engine lifting bracket
The pins are .500 x 2.375 that fit into the bracket and have a .750 x .500 length head. The over all length is 2.875 including the head .
A picture and let me know if I can help as I have a machine shop
Attached Images
File Type: jpg image.jpg (31.6 KB, 266 views)
__________________
Wanted Ford oiler oil cans Thanks
hop up is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-23-2024, 10:47 AM   #3
petehoovie
Senior Member
 
petehoovie's Avatar
 
Join Date: May 2015
Posts: 10,154
Default Re: KR Wilson engine lifting bracket
Quote:
Originally Posted by BlueNotes View Post
I recently scored a repro KRW engine lifting bracket but the 2 knurled pins are missing. Can anyone advise the measures (or a simple drawing) for the pin so I can make them?
petehoovie is offline   Reply With Quote
Old 04-23-2024, 10:47 AM   #4
petehoovie
Senior Member
 
petehoovie's Avatar
 
Join Date: May 2015
Posts: 10,154
Default Re: KR Wilson engine lifting bracket
Quote:
Originally Posted by hop up View Post
The pins are .500 x 2.375 that fit into the bracket and have a .750 x .500 length head. The over all length is 2.875 including the head .
A picture and let me know if I can help as I have a machine shop
petehoovie is offline   Reply With Quote
Old 04-23-2024, 11:11 AM   #5
BlueNotes
Senior Member
 
Join Date: May 2010
Location: Land of the Midnight Sun
Posts: 182
Default Re: KR Wilson engine lifting bracket
Quote:
Originally Posted by hop up View Post
The pins are .500 x 2.375 that fit into the bracket and have a .750 x .500 length head. The over all length is 2.875 including the head .
A picture and let me know if I can help as I have a machine shop
Thank you very much @hop up! That's all I need to make them.
BlueNotes is offline   Reply With Quote
Old 04-23-2024, 02:17 PM   #6
GB SISSON
Senior Member
 
GB SISSON's Avatar
 
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 5,881
Default Re: KR Wilson engine lifting bracket
Sponsored Links (Register now to hide all advertisements)
Could somebody post a photo of one of these in action? I'm not seeing how it works.
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1946 Tonner Pickup with 226 H six, 1979 Toyota landcruiser wagon, now wearing 1947 Ford Jailbar sheet metal. 'Rusty ol' floorboards, hot on their feet' (Alan Jackson)
GB SISSON is offline   Reply With Quote
Old 04-23-2024, 02:45 PM   #7
BlueNotes
Senior Member
 
Join Date: May 2010
Location: Land of the Midnight Sun
Posts: 182
Default Re: KR Wilson engine lifting bracket
It fits in the valley and the two pins drop inside the heat risers.
Attached Images
File Type: jpg KR WILSON 6000 E .jpg (35.3 KB, 212 views)
BlueNotes is offline   Reply With Quote
Old 04-23-2024, 02:58 PM   #8
petehoovie
Senior Member
 
petehoovie's Avatar
 
Join Date: May 2015
Posts: 10,154
Default Re: KR Wilson engine lifting bracket
Quote:
Originally Posted by BlueNotes View Post
It fits in the valley and the two pins drop inside the heat risers.
petehoovie is offline   Reply With Quote
Old 04-23-2024, 03:15 PM   #9
Tim Ayers
Senior Member
 
Join Date: May 2010
Location: NJ
Posts: 6,920
Default Re: KR Wilson engine lifting bracket
Quote:
Originally Posted by BlueNotes View Post
It fits in the valley and the two pins drop inside the heat risers.
Yep. I believe you can flip it 180 degrees to have the motor angled either forward or back, right? The offset changes the angel the motor will hang.
Tim Ayers is online now   Reply With Quote
Old 04-23-2024, 04:38 PM   #10
Ronnieroadster
Senior Member
 
Ronnieroadster's Avatar
 
Join Date: Dec 2010
Location: East Coast in CT
Posts: 1,697
Default Re: KR Wilson engine lifting bracket
Quote:
Originally Posted by Tim Ayers View Post
Yep. I believe you can flip it 180 degrees to have the motor angled either forward or back, right? The offset changes the angel the motor will hang.

Tim from my experience using the KR Wilson one I have if its turned around the lifting bracket will not sit flat on the inside surface of the valve chamber.
Ronnieroadster
__________________
I use the F word a lot no not that word these words Flathead, Focus and Finish
"Life Member of the Bonneville 200 MPH Club using a Ford Flathead block
First Ford Flathead bodied roadster to run 200 MPH Record July 13, 2018 LTA timing association 200.921
First Ford flathead roadster to run 200 MPH at Bonneville Salt Flats setting the record August 7th 2021 at 205.744 MPH reset the record in 2024 to 211.830 running to mile four. Top speed 2024 mile five 220.672 exit speed 221.587
Ronnieroadster is offline   Reply With Quote
Old 04-23-2024, 05:29 PM   #11
GB SISSON
Senior Member
 
GB SISSON's Avatar
 
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 5,881
Default Re: KR Wilson engine lifting bracket
Perhaps in the other position it's for if a transmission is attached?
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1946 Tonner Pickup with 226 H six, 1979 Toyota landcruiser wagon, now wearing 1947 Ford Jailbar sheet metal. 'Rusty ol' floorboards, hot on their feet' (Alan Jackson)
GB SISSON is offline   Reply With Quote
Old 04-23-2024, 10:35 PM   #12
outlaw
Senior Member
 
Join Date: May 2010
Location: Eagle River,Alaska
Posts: 370
Default Re: KR Wilson engine lifting bracket
I made a adjustable lifting plate for my flatheads.
Attached Images
File Type: jpg 20180512_195546.jpg (63.4 KB, 150 views)
outlaw is offline   Reply With Quote
Old 04-23-2024, 11:24 PM   #13
mercman from oz
Senior Member
 
mercman from oz's Avatar
 
Join Date: May 2012
Location: Queensland, Australia
Posts: 12,013
Default Re: KR Wilson engine lifting bracket


adjustable lifting plate - outlaw
mercman from oz is offline   Reply With Quote
Old 04-24-2024, 07:04 AM   #14
rockfla
Senior Member
 
rockfla's Avatar
 
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 4,806
Default Re: KR Wilson engine lifting bracket
I got this one off ebay and works great.
Attached Images
File Type: jpg Prep1.jpg (50.6 KB, 109 views)
File Type: jpg Assembly10.jpg (49.5 KB, 102 views)
rockfla is offline   Reply With Quote
Old 04-24-2024, 07:24 AM   #15
Tim Ayers
Senior Member
 
Join Date: May 2010
Location: NJ
Posts: 6,920
Default Re: KR Wilson engine lifting bracket
Quote:
Originally Posted by Ronnieroadster View Post
Tim from my experience using the KR Wilson one I have if its turned around the lifting bracket will not sit flat on the inside surface of the valve chamber.
Ronnieroadster
Ahh. Interesting. I don't own one, but I've thought that's how it worked. Thanks for setting me straight. I've been on the hunt for one for years. They've all seem to have disappeared.
Tim Ayers is online now   Reply With Quote
Old 04-24-2024, 11:04 AM   #16
petehoovie
Senior Member
 
petehoovie's Avatar
 
Join Date: May 2015
Posts: 10,154
Default Re: KR Wilson engine lifting bracket
Quote:
Originally Posted by rockfla View Post
I got this one off ebay and works great.


petehoovie is offline   Reply With Quote
Reply

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:55 PM.