01-17-2016, 12:52 PM
|
#1 |
|
Senior Member
Join Date: May 2010
Location: Auburn Washington
Posts: 2,662
|
wide box
I`m sure this was brought up before. does someone reproduce rear steel fenders for the wide box. John
|
|
|
|
01-17-2016, 02:55 PM
|
#2 |
|
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,428
|
Re: wide box
Not to my knowledge. Google: Westcott's. Quality, been around a looong time and Karl posts on F/barn.
Paul in CT |
|
|
|
| Sponsored Links (Register now to hide all advertisements) |
|
|
|
01-17-2016, 07:53 PM
|
#3 |
|
Senior Member
Join Date: May 2010
Location: Southbridge, Ma.
Posts: 1,614
|
Re: wide box
You could consider what I did on my huckster, bolt up regular pickup fenders and slice them in the middle and weld up to match the outside of the running board. I think regular fenders are about an inch too wide.
|
|
|
|
|
01-17-2016, 08:01 PM
|
#4 |
|
Senior Member
Join Date: Jun 2015
Location: Signal Mtn, TN (SE TN)
Posts: 2,591
|
Re: wide box
Hey john
They are not repo'd except fiberglass as I know They can be made best by slicing and dicing sedan fenders. Yep I know they are not easy to find too Making them from coupe/roadster is much harder. I've tried both ways! Bill U |
|
|
|
|
01-17-2016, 08:12 PM
|
#5 |
|
Senior Member
Join Date: Jun 2010
Posts: 141
|
Re: wide box
I have an old Mack Products Catalogue which shows such steel fenders for the wide box.
Not sure if they still make them. They are also known as Mack Hils Inc in Moberly Missouri Ph 660 263 7444 Good luck... |
|
|
|
|
01-17-2016, 10:19 PM
|
#6 |
|
Senior Member
Join Date: May 2010
Location: Clinton,WA/Whidbey Island
Posts: 4,457
|
Re: wide box
Sponsored Links (Register now to hide all advertisements)
__________________
www.whidbeymodelaclub.com |
|
|
|
|
01-17-2016, 11:55 PM
|
#7 |
|
Senior Member
Join Date: Jun 2010
Posts: 141
|
Re: wide box
Hash, you may have struck GOLD with this lead.
I hope they still make them... |
|
|
|
|
01-17-2016, 11:57 PM
|
#8 |
|
Senior Member
Join Date: May 2010
Location: Kenosha, WI
Posts: 1,099
|
Re: wide box
Hi John,
I have a few photos comparing a nos wide bed fender to an early take off coupe/roadster rear fender. Note the inner lip is larger than the coupe. Also the wide bed fender in 10" in with and the coupe is 12" in with. Also the inner/outer rear area below the rear mounting bracket is shaped diff.than coupe or sedan. Jim Sinclair |
|
|
|
|
01-18-2016, 01:10 AM
|
#9 | |
|
Senior Member
Join Date: May 2010
Location: Florida between Sarasota and TampaSouth Florida
Posts: 14,054
 |
Re: wide box
Quote:
" We supply truck bed parts for Dodge, Willys, Studebaker and Plymouth. Complete assembled beds or kits are also available for Chevrolet 1928 through 1972 and Fords 1928 through 1972. Contact us for a quotation and shipping costs on any of these kits or custom beds at [email protected]." Mack Hils, Inc. Address: 544 North Avenue Mailing: P.O. Box 856 Moberly, MO 65270 Phone: (660) 263-7444 Fax: (660) 263-4403 Hours: 7am - 5pm (CDT)
__________________
What's right about America is that although we have a mess of problems, we have great capacity - intellect and resources - to do some thing about them. - Henry Ford II |
|
|
|
|
|
01-18-2016, 02:01 AM
|
#10 |
|
Senior Member
Join Date: May 2010
Location: Auburn Washington
Posts: 2,662
|
Re: wide box
thanks Jim for the pictures and size. it looks like I will be cutting down some fenders.
John |
|
|
|
|
01-18-2016, 04:05 PM
|
#11 |
|
Senior Member
Join Date: May 2010
Location: brentwood, ca
Posts: 4,420
|
Re: wide box
pm sent. Bob
|
|
|
 |
«
Previous Thread
|
Next Thread
»
Linear Mode
|
|
| Sponsored Links (Register now to hide all advertisements) |
|
|
All times are GMT -5. The time now is 01:22 PM.