Forum: Model A (1928-31)
05-05-2024, 05:14 PM
|
Replies: 13
Views: 877
|
Forum: Model A (1928-31)
05-05-2024, 10:45 AM
|
Replies: 6
Views: 723
Re: weird stuff
Just out of curiosity, are the pistons slotted on both sides or just one side?
|
Forum: Model A (1928-31)
05-01-2024, 09:32 AM
|
Replies: 25
Views: 1,889
Re: Motor Meter or Quail
I have the repro Motor Meters on both of my A's and they work exactly as intended, I am very happy with them, never a problem. No I have no connection with Vintique.
|
Forum: Model A (1928-31)
04-26-2024, 02:32 PM
|
Replies: 26
Views: 2,288
|
Forum: Model A (1928-31)
04-21-2024, 10:18 AM
|
Replies: 6
Views: 674
|
Forum: Model A (1928-31)
04-09-2024, 09:48 AM
|
Replies: 31
Views: 2,651
|
Forum: Early V8 (1932-53)
04-03-2024, 02:10 PM
|
Replies: 10
Views: 728
|
Forum: Model A (1928-31)
03-30-2024, 03:53 PM
|
Replies: 31
Views: 2,651
Re: V8 Clutch in Model A: Something is not right
When you tighten up the pressure plate do the release fingers come close to the center of clutch disc not allowing much travel for clutch to release when stepping on pedal? If the disc is too thick...
|
Forum: Model A (1928-31)
03-29-2024, 07:26 AM
|
Replies: 19
Views: 1,828
|
Forum: Model A (1928-31)
03-28-2024, 12:37 PM
|
Replies: 19
Views: 1,828
Re: Timing gears
I would guess an outside supplier, they are often marked "Celoron"
|
Forum: Model A (1928-31)
03-27-2024, 09:42 AM
|
Replies: 19
Views: 1,828
|
Forum: Model A (1928-31)
03-26-2024, 06:05 PM
|
Replies: 12
Views: 894
|
Forum: Model A (1928-31)
03-17-2024, 08:03 PM
|
Replies: 7
Views: 716
|
Forum: Model A (1928-31)
03-09-2024, 03:28 PM
|
Replies: 28
Views: 5,457
|
Forum: Model A (1928-31)
03-07-2024, 11:10 AM
|
Replies: 28
Views: 5,457
Re: Main bearing bolts
The original bolts were a snug fit in the block. You would tighten up the nut, after positioning the cotter pin hole in the bolt for best installation. This snugness is what centers the main cap on...
|
Forum: Model A (1928-31)
03-04-2024, 03:08 PM
|
Replies: 73
Views: 4,979
Re: Value of an Un-Restored Model A Engine
Don't scrap them, there may be some good stuff there!! I am running a block that had been laying on the ground outdoors for years, it did need to be bored .100 oversize on the cylinders but it is...
|
Forum: Model A (1928-31)
02-22-2024, 11:21 AM
|
Replies: 17
Views: 1,091
Re: What the heck just happened ? (electrical)
I agree. Not to pile on here but if the car is positive ground your first connection of ground clamp to head bolt was reverse polarity and electronics usually if not always turn up their toes on that...
|
Forum: Model A (1928-31)
02-21-2024, 03:13 PM
|
Replies: 10
Views: 757
|
Forum: Model A (1928-31)
02-18-2024, 10:49 AM
|
Replies: 6
Views: 666
|
Forum: Model A (1928-31)
02-15-2024, 12:31 PM
|
Replies: 24
Views: 1,392
|
Forum: Model A (1928-31)
02-13-2024, 06:40 PM
|
Replies: 8
Views: 556
|
Forum: Model A (1928-31)
02-11-2024, 11:52 AM
|
Replies: 6
Views: 642
|
Forum: Model A (1928-31)
02-10-2024, 11:00 AM
|
Replies: 27
Views: 1,876
|
Forum: Model A (1928-31)
02-08-2024, 09:44 AM
|
Replies: 63
Views: 5,713
|
Forum: Model A (1928-31)
02-07-2024, 12:11 PM
|
Replies: 22
Views: 1,984
|