Forum: Model A (1928-31)
01-07-2024, 02:54 PM
|
Replies: 24
Views: 2,444
Re: ?When to Pull the Tank?
Gents,
For some of you it might help to give the closure showing what i did and the reults.
I ended up seeing the tina shin video on youtube, i heard she's the new Tech Director for MAFCA....
|
Forum: Model A (1928-31)
12-31-2023, 11:51 AM
|
Replies: 4
Views: 537
Battery Box ‘28
The battery box or hanger on my ‘28 has been a disaster to the eyes, but saving up to replace it has ended in some disappointment. The new Snyder’s unit does not seem to match whatsoever. Can...
|
Forum: Model A (1928-31)
12-29-2023, 12:39 AM
|
Replies: 12
Views: 913
|
Forum: Model A (1928-31)
12-20-2023, 08:31 PM
|
Replies: 18
Views: 1,248
Re: Clutch Adjusting Yoke
has anyone ever used one of these fully threaded units on the multi-disc clutch? I was recently disappointed when i noticed nobody sells a pre-Nov '28 version of this part - nor do they tell you in...
|
Forum: Model A (1928-31)
12-20-2023, 11:26 AM
|
Replies: 24
Views: 2,444
?When to Pull the Tank?
Can i get any guidance on when to pull and clean the gas tank? Seems like a lot of work without too much to gain. But, the engine and transmission are already out and i'm trying to get everything...
|
Forum: Model A (1928-31)
11-16-2023, 07:40 PM
|
Replies: 16
Views: 1,692
Re: Multi plate clutch service part
Joe, is there any way that I could buy this from you? Natick said he would hold it for me but you got there first😒. I’ve got a down car in need.
|
Forum: Model A (1928-31)
11-11-2023, 03:40 PM
|
Replies: 8
Views: 1,100
Re: 28 oil pan question?
The pump has a screen around it and the best thing about the clean out feature on the ‘28 is you can pull the pump and screen without dropping the entire pan. No it’s not hard at all to put the pump...
|
Forum: Model A (1928-31)
11-11-2023, 03:25 PM
|
Replies: 21
Views: 1,992
Re: new distributor?
Highly recommend the new castings from Snyder’s. These come with bushings installed and reamed. Remainder of the parts are also available on Snyder’s.
|
Forum: Model A (1928-31)
11-11-2023, 03:19 PM
|
Replies: 16
Views: 1,502
Re: Bearing clearance
Randall, I just had to say that your videos have been an amazing help for my rebuild lately. Please keep them coming!
|
Forum: Model A (1928-31)
11-11-2023, 03:10 PM
|
Replies: 22
Views: 2,615
Re: At a lost here
Because of the dipper tray being so challenging to remove, it’s possible to have debris in the pan going unnoticed for a very long time. You may also check the condition of the rear labyrinth seal...
|
Forum: Model A (1928-31)
11-11-2023, 11:31 AM
|
Replies: 12
Views: 2,492
Re: Bendix Spring bolts
The fastener threads must somehow be tight to prevent the threads from moving. Retainer compound is a very good suggestion in addition to the clips.
|
Forum: Model A (1928-31)
11-11-2023, 10:26 AM
|
Replies: 8
Views: 763
Re: Piston Ring Gap Question
You said "out of the box" and I just wanted to clarity how they should be measured. Plese be sure you're measuring the gap(s) when the ring(s) are installed into the bore. This will be the in-situ...
|
Forum: Model A (1928-31)
11-11-2023, 10:18 AM
|
Replies: 8
Views: 678
|
Forum: Model A (1928-31)
11-11-2023, 10:04 AM
|
Replies: 13
Views: 1,634
Re: Exhaust Manifold crack
definitely don't just buy a new manifold and just bolt it up. The instructions from Snyders clearly detail how the manifolds are not going to fit properly until they're machined. This is a trap...
|
Forum: Model A (1928-31)
11-11-2023, 09:12 AM
|
Replies: 16
Views: 1,692
Re: Multi plate clutch service part
Yes RotorWrench - I've got something along those lines in my car now. I'd like to share photos and start a new thread but it says i have to post 10 times before i'm allowed to share images! I guess...
|
Forum: Model A (1928-31)
11-10-2023, 04:18 PM
|
Replies: 16
Views: 1,692
Re: Multi plate clutch service part
I'm pretty impressed with this repair i must say. I'm considering something similar for my car, however i'm not sure how much damage to the splines would justify it.
|