Forum: Early V8 (1932-53)
05-16-2024, 07:33 PM
|
Replies: 36
Views: 1,528
Re: Oil leak
What oil pump do you have in there ? With the engines with a slinger at the rear I like a stock pump and a rather tight clearance on the rear main crankshaft journal.
|
Forum: Early V8 (1932-53)
05-14-2024, 07:05 PM
|
Replies: 14
Views: 576
Re: 1940 Ford Zenith Radio
I’ve sent three 40 radios to this guy. Reasonable and quick turnaround. https://www.car-radio-conversions.com/
|
Forum: Early V8 (1932-53)
05-12-2024, 12:18 PM
|
Replies: 5
Views: 480
|
Forum: Early V8 (1932-53)
05-09-2024, 11:22 PM
|
Replies: 16
Views: 693
Re: 1947 Rear Axle Worn Down
Remove the drivers side axle housing and the passenger side hub and drum along with the key and the whole unit with the differential , ring gear and axels will slide out.
|
Forum: Early V8 (1932-53)
05-08-2024, 11:41 PM
|
Replies: 16
Views: 693
|
Forum: Early V8 (1932-53)
05-08-2024, 07:38 AM
|
Replies: 11
Views: 527
|
Forum: Early V8 (1932-53)
05-06-2024, 08:38 PM
|
Replies: 11
Views: 527
Re: Front Brake Hose
No, just looking for a replacement hose without having to wait a week to get it.
|
Forum: Early V8 (1932-53)
05-06-2024, 07:37 PM
|
Replies: 13
Views: 614
|
Forum: Early V8 (1932-53)
05-06-2024, 07:23 PM
|
Replies: 11
Views: 527
Front Brake Hose
Anyone have a modern replacement number for the 91A-2079 front wheel brake hoses? Thanks
|
Forum: Early V8 (1932-53)
05-03-2024, 10:43 AM
|
Replies: 21
Views: 778
|
Forum: Early V8 (1932-53)
05-02-2024, 02:59 PM
|
Replies: 6
Views: 589
|
Forum: Early V8 (1932-53)
04-28-2024, 05:54 PM
|
Replies: 9
Views: 572
Re: 8BA Bell housing
So, to go the other way using the Mercury bell housing I can use the truck starter plate and use the seal . I have both starter plates but only have a Mercury bell housing.
|
Forum: Early V8 (1932-53)
04-28-2024, 05:39 PM
|
Replies: 9
Views: 572
8BA Bell housing
When using the 8BA truck bell housing with the large round bolt circle for the transmission does it matter weather or not if you use the stamped steel Mercury bell housing as long as you use the...
|
Forum: Early V8 (1932-53)
04-26-2024, 02:32 PM
|
Replies: 17
Views: 1,167
|
Forum: Early V8 (1932-53)
04-23-2024, 01:55 PM
|
Replies: 3
Views: 477
|
Forum: Early V8 (1932-53)
04-23-2024, 12:48 PM
|
Replies: 6
Views: 589
Re: Lincoln pinion backlash
I have it written down with other notes and bearing and pinion seal number from when I rebuilt my 39 Zephyr rear axle. . I’m away from the shop now but maybe later this afternoon.
|
Forum: Early V8 (1932-53)
04-20-2024, 08:51 PM
|
Replies: 7
Views: 498
|
Forum: Early V8 (1932-53)
04-18-2024, 09:26 AM
|
Replies: 4
Views: 630
|
Forum: Early V8 (1932-53)
04-18-2024, 09:22 AM
|
Replies: 20
Views: 1,573
|
Forum: Early V8 (1932-53)
04-17-2024, 10:18 PM
|
Replies: 95
Views: 6,075
|
Forum: Early V8 (1932-53)
04-14-2024, 12:52 PM
|
Replies: 4
Views: 773
Re: Helmet Distributor Issues
If you block off the passenger side points the driver side should be set at 22 1/2 degrees dwell. Then remove the block and set the passenger side to obtain 36 degrees total.
|
Forum: Early V8 (1932-53)
04-12-2024, 10:26 PM
|
Replies: 6
Views: 523
Re: Cam Specs Again
That’s what I’m thinking also. Based on the looks of the top of the lobes it has a lot of duration.
|
Forum: Early V8 (1932-53)
04-12-2024, 07:08 PM
|
Replies: 6
Views: 523
Re: Cam Specs Again
It’s an old regrind but never run. It’s in an Isky box but not sure it’s an Isky cam.
|
Forum: Early V8 (1932-53)
04-12-2024, 05:15 PM
|
Replies: 6
Views: 523
Cam Specs Again
Picked up this 8BA cam yesterday. Has no card in the box. Anyone have any information about it ? Thanks
|
Forum: Early V8 (1932-53)
04-11-2024, 09:44 PM
|
Replies: 7
Views: 426
|