Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Page 1 of 20 1 234511 Last »
Showing results 1 to 25 of 500
Search took 0.05 seconds. Search: Posts Made By: jimvette59
Forum: Model A (1928-31) Today, 07:05 AM
Replies: 15
Views: 517
Posted By jimvette59
Re: how to repair top casting on sidebowl carburetor???

Done that on my 31 side bowl, had it welded, cleaned it up with a Dermal.
Forum: Early V8 (1932-53) Today, 06:57 AM
Replies: 12
Views: 259
Posted By jimvette59
Re: engine stumbles under load

If you do not have a ballast resister install one and or check the coil to see if it has a resister in it or not. JMO
Forum: Early V8 (1932-53) 05-18-2024, 07:21 AM
Replies: 19
Views: 773
Posted By jimvette59
Re: '46 Coupe 59AB Starter

Hi 51 Woodie, I would use it if it checked out on a growler and new brushes,springs,bushing front and rear, new Bendix. Also a spray can or two of electro clean. JMO.
Forum: Late V8 (1954+) 05-14-2024, 06:10 AM
Replies: 8
Views: 307
Posted By jimvette59
Re: Timken a150 pinion seal

Googled your truck and found it on line, it is available.
Forum: Model A (1928-31) 05-13-2024, 06:57 AM
Replies: 14
Views: 670
Posted By jimvette59
Re: Next problem is... locked rear brakes

Did you try to put the axle in the puller first then behind the collar? JMO
Forum: Model A (1928-31) 05-13-2024, 06:52 AM
Replies: 7
Views: 504
Posted By jimvette59
Re: Shifting to reverse

Did you try to shift to second,third,first then reverse. Try it a couple of times. IMO
Forum: Early V8 (1932-53) 05-03-2024, 05:49 AM
Replies: 10
Views: 470
Posted By jimvette59
Re: Mechanical vacuum brake boosters

Look at the 55,56 Thunderbird brake booster, They have been used for a long time. JMO
Forum: Model-T 05-01-2024, 03:46 PM
Replies: 14
Views: 4,331
Posted By jimvette59
Re: WTB 26 27 ford roadster lower windshield frame

Btt
Forum: Model-T 04-20-2024, 06:38 AM
Replies: 0
Views: 371
Posted By jimvette59
Door hinges

Hi I'm looking for the pillar parts of the hinges for my 27 ford roadster. I have the door parts of the hinges. Thank you for looking. Jim T.
Forum: Early V8 (1932-53) 04-18-2024, 08:04 AM
Replies: 10
Views: 709
Posted By jimvette59
Re: master cylinder

Are you using double flares ?
Forum: Model A (1928-31) 04-16-2024, 06:16 AM
Replies: 6
Views: 601
Posted By jimvette59
Ford badge

What is the name of the color blue on the ford badge ?
Forum: Model T (1909-1927) 03-14-2024, 05:31 PM
Replies: 4
Views: 787
Posted By jimvette59
Re: Carb

It looks like the carb that was on our Owens Boat that had a six cyl Hercules engine.
Forum: Early V8 (1932-53) 03-03-2024, 07:47 AM
Replies: 14
Views: 1,108
Posted By jimvette59
Re: How I did it.

Hi Roger, I did convert my 255 Merc. engine to 12 Volts and I did experience the 6 Volt problem. What I did was to purchase a new 12 Volt starter for a T bird on line, It cost about 68.00 shipped, I...
Forum: Model-A 02-21-2024, 07:07 AM
Replies: 2
Views: 467
Posted By jimvette59
Re: Model A rear axle housings

Btt
Forum: Early V8 (1932-53) 02-15-2024, 06:28 PM
Replies: 12
Views: 680
Posted By jimvette59
Re: carb jet size

Yes I did find it loose a while ago and tightened It. I will check it out again. Who has the best rebuild parts or kit ?
Forum: Early V8 (1932-53) 02-15-2024, 06:23 PM
Replies: 12
Views: 680
Posted By jimvette59
Re: carb jet size

flatjack9 It's a 8BA.
Forum: Early V8 (1932-53) 02-15-2024, 11:51 AM
Replies: 12
Views: 680
Posted By jimvette59
carb jet size

H I I have a 94 carb on a 255 merc stock engine and feel it's running to rich. I'd like to know the proper size jets. I think 54's are in there. Thanks Jim T.
Forum: Early V8 (1932-53) 02-11-2024, 03:09 PM
Replies: 21
Views: 2,306
Posted By jimvette59
Re: Third Gen Automotive

It's good to hear from you Michael. It will take time to catch up. Keep The Faith !
Forum: Early V8 (1932-53) 01-29-2024, 08:01 AM
Replies: 28
Views: 1,779
Posted By jimvette59
Re: Leaking waterpump 60hp

YUP it needs to be repaired or replaced. That's why that hole is there.
Forum: Model-A 01-28-2024, 08:54 AM
Replies: 2
Views: 467
Posted By jimvette59
Re: Model A rear axle housings

btt
Forum: Early V8 (1932-53) 01-28-2024, 08:51 AM
Replies: 88
Views: 7,140
Posted By jimvette59
Re: Clutch Chatter

Call Fort Wane Clutch.
Forum: Model A (1928-31) 01-22-2024, 02:17 PM
Replies: 9
Views: 1,088
Posted By jimvette59
Re: Torque Tube Bushing

What's wrong with the original bearing ? It looks like the sleeve is not seated .
Forum: Model-A 01-22-2024, 10:56 AM
Replies: 2
Views: 467
Posted By jimvette59
Model A rear axle housings

I need two rear axle housing ENDS ONLY with good spring perches and balls for a project. Thank you for looking Jim T.
Forum: Early V8 (1932-53) 01-21-2024, 09:43 AM
Replies: 13
Views: 645
Posted By jimvette59
Re: 3049 Remflex exhaust manifold gasket set

Check your flange that is welded to the 90 deg.ell for flatness and install more hangers. JMHO
Forum: Early V8 (1932-53) 01-14-2024, 09:23 AM
Replies: 8
Views: 595
Posted By jimvette59
Re: Carb Icing

We need a picture of the Intake manifold .
Showing results 1 to 25 of 500
Page 1 of 20 1 234511 Last »

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:21 PM.