Forum: Questions & Suggestions
07-11-2023, 12:44 PM
|
Replies: 0
Views: 712
CarPart Pro Scam ?
Dear Staff members,
as reported yesterday, I received through one of the Ford Barn members a message with e-mail address where I could buy rear brake drums. This in answer to my add : "wanted"...
|
Forum: Early V8 (1932-53)
07-10-2023, 05:42 AM
|
Replies: 8
Views: 1,115
Carpart Pro Scam ??
Dear Forum readers,
I was looking for early V8 rear brake drums (1948) which unfortunately could not be found in the "Swap" adds.
Via the forum I received the advice to ask "Car Part Pro " if...
|
Forum: Questions & Suggestions
07-10-2023, 03:06 AM
|
Replies: 0
Views: 578
Car Part Pro Fraud warning
Dear Forum readers,
I was looking for early V8 rear brake drums (1948) which unfortunately could not be found in the "Swap" adds.
Via the forum I received the advice to ask "Car Part Pro " if...
|
Forum: Early V8
06-22-2023, 09:25 AM
|
Replies: 1
Views: 340
|
Forum: Early V8
06-22-2023, 09:18 AM
|
Replies: 1
Views: 340
1948 rear brake drums
Wanted: Dear all, 1 or 2 usable rear drums for early Ford V8 1948.
Inner diameter 12 "
These drums have the hub on the outside.
Thanks in advance, Hans Schrijver, The Netherlands
|
Forum: Early V8 (1932-53)
06-04-2023, 03:32 PM
|
Replies: 4
Views: 810
|
Forum: Model T (1909-1927)
06-04-2023, 03:09 PM
|
Replies: 8
Views: 2,140
|
Forum: Early V8 (1932-53)
06-04-2023, 02:59 PM
|
Replies: 2
Views: 432
|
Forum: Early V8 (1932-53)
06-04-2023, 02:31 PM
|
Replies: 10
Views: 986
Re: brakes
Normaly bleeding the air from an hydraulic system is straight forward and should not be that difficult, but it could be that ...........
1-The new seals /parts in the master cilinder are not the...
|
Forum: Early V8 (1932-53)
06-04-2023, 02:10 PM
|
Replies: 3
Views: 618
|
Forum: Early V8 (1932-53)
06-04-2023, 01:51 PM
|
Replies: 16
Views: 1,573
Re: Camber wrong on ‘35
Dear all,
when talking about Camber, does anyone know what would be the recommended Caster angle when the car is used for racing? I have an A Ford chassis used as base for an Indy race car, bulid...
|
Forum: Model A (1928-31)
06-04-2023, 01:34 PM
|
Replies: 9
Views: 1,239
Re: Rivet source
keep in mind you need a lot of heat and of course the tools on both sides of the rivet
|
Forum: Early V8 (1932-53)
06-03-2023, 04:32 PM
|
Replies: 180
Views: 395,156
Re: Hey Fellas... Some Clarification...
Dear all,
Also my Ford is not standard, it's custom made in the 50's , build on a 37 Ford chassis with a 48 rear axle, but I'm sure you will like it when it is ready.
Indy race cars were often...
|
Forum: Model T (1909-1927)
06-02-2023, 05:40 AM
|
Replies: 3
Views: 1,562
|
Forum: Early V8 (1932-53)
05-30-2023, 03:55 PM
|
Replies: 12
Views: 3,758
Re: How to remove the Rear Pinion?
Dear all, I'm just in the process of overhauling the rear axle of an early ford V8, all parts came out OK, except the pinion gear. I wondered how to get it out........, now I know!
Many thanks
(...
|