Forum: Model A (1928-31)
Yesterday, 09:36 PM
|
Replies: 2
Views: 169
|
Forum: Model A (1928-31)
Yesterday, 06:29 PM
|
Replies: 2
Views: 169
Sidemount irons - 1930 Coupe
How do I tell the difference between right and left irons for the front fender sidemounts.
Photo shows iron on left (from drivers side) and iron on right (passenger side) look the same.
Mounted...
|
Forum: Model A (1928-31)
05-05-2024, 03:14 PM
|
Replies: 13
Views: 997
|
Forum: Model A (1928-31)
05-02-2024, 07:49 PM
|
Replies: 13
Views: 997
|
Forum: Model A (1928-31)
05-02-2024, 07:46 PM
|
Replies: 13
Views: 997
Re: Rear spring shackle installation
Success. Just took me a bit of perseverance in tight quarters. I couldn't use Mr Benson's method. I tried but the bottom lip on the spreader bar is lower than the spring end, so it dug into the...
|
Forum: Model A (1928-31)
04-29-2024, 04:28 PM
|
Replies: 13
Views: 997
|
Forum: Model A (1928-31)
04-29-2024, 11:15 AM
|
Replies: 13
Views: 997
Re: Rear spring shackle installation
Thanks JayJay. I will do as you recommend. I was just getting a little nervous about the tension. Doing it equal in both sides. I took out the shackle that was half way in to free the rear end up...
|
Forum: Model A (1928-31)
04-29-2024, 10:43 AM
|
Replies: 13
Views: 997
|
Forum: Model A (1928-31)
04-28-2024, 09:49 PM
|
Replies: 13
Views: 997
Re: Rear spring shackle installation
I am using the spreader that goes the length of the spring. I guess I am just getting a bit nervous because of the tension and that the rear end is cocked a little. Photo is of the passengers side...
|
Forum: Model A (1928-31)
04-28-2024, 09:17 PM
|
Replies: 13
Views: 997
Rear spring shackle installation
Gentlemen:
I am having trouble lining up the spring and perch to insert the rear shackles.
I have the passengers side (right side) almost in but the rear end seems to be cocked at an angle....
|
Forum: Model A (1928-31)
04-15-2024, 07:01 PM
|
Replies: 2
Views: 513
Re: Rear backing plate order of assembly
Thanks JayJay. This was the key element that I needed "Add backing plates using the two rear (short) bolts, loosely tightened" to know first step. Thanks very much for your thoughtful response. ...
|
Forum: Early V8
04-13-2024, 09:28 PM
|
Replies: 0
Views: 167
|
Forum: Model A (1928-31)
04-13-2024, 08:47 PM
|
Replies: 2
Views: 513
Rear backing plate order of assembly
Gents
Please advise the best order of assembly.
I had rear brakes/backing plates rebuilt by Randy Gross - great job and amazingly fast turnaround! Thanks Randy.
So now I have the rear...
|
Forum: Model A (1928-31)
07-22-2023, 05:08 PM
|
Replies: 9
Views: 1,364
|
Forum: Model A (1928-31)
07-22-2023, 12:50 PM
|
Replies: 9
Views: 1,364
|
Forum: Model A (1928-31)
07-22-2023, 12:47 PM
|
Replies: 9
Views: 1,364
Re: Rear spring perch fix procedure
Brent
Thanks so much for your good advice. Fortunately I do have another axle housing I can use.
I'll get the existing one off first to see how badly it is worn, and if salvageable, use that to...
|
Forum: Model A (1928-31)
07-22-2023, 10:22 AM
|
Replies: 9
Views: 1,364
Re: Rear spring perch fix procedure
Thanks. For reassembly I do have a rear spring spreader. Thanks, I just didn't want to proceed without checking first if I was overlooking something.
|
Forum: Model A (1928-31)
07-22-2023, 08:41 AM
|
Replies: 9
Views: 1,364
Rear spring perch fix procedure
Gents:
I just powder coated wheels for a 1930 coupe driver that I just picked up locally. So happy to dress up the black plain-Jane coupe! When removing the drivers side wheel, I was horrified...
|
Forum: Model A (1928-31)
06-30-2023, 01:30 PM
|
Replies: 13
Views: 1,498
Re: Timing Gear Replacement
Gents - I used the impact wrench. First try nothing. Second try nothing. Third try the nut spun off, so easily I thought I dreamt it!!!
Thanks for the great advice.
Don
|
Forum: Model A (1928-31)
06-28-2023, 03:37 PM
|
Replies: 13
Views: 1,498
Re: Timing Gear Replacement
Thanks very much for your advice. I do have an impact wrench and the special socket for the nut. I will try that first before any heat.
Thanks again.
|
Forum: Model A (1928-31)
06-28-2023, 03:07 PM
|
Replies: 13
Views: 1,498
Timing Gear Replacement
Model A Gurus - I need some advice:
Attempted to remove the timing gear on an engine rebuilt 40 years ago but on the shelf and never installed. Assembled the engine, but saw a small chip on one...
|
Forum: Model A (1928-31)
12-30-2021, 07:49 PM
|
Replies: 20
Views: 3,268
|
Forum: Model A (1928-31)
12-30-2021, 07:34 PM
|
Replies: 31
Views: 2,879
Re: Assembly - fan to water pump
Thanks to all for your comments and suggestions. I ground down the pump housing casting where it was a bit oblong. I placed the spacer with Allen set screw between the fan and the casting end to...
|
Forum: Model A (1928-31)
12-23-2021, 12:07 PM
|
Replies: 31
Views: 2,879
Re: Assembly - fan to water pump
Thanks Keith, will check the measurements again and if I need to bring it back some, maybe I can use a teflon flat washer that is included with the spacer (which I don't need!). The partition in the...
|
Forum: Model A (1928-31)
12-20-2021, 03:58 PM
|
Replies: 31
Views: 2,879
|