Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Page 1 of 20 1 234511 Last »
Showing results 1 to 25 of 500
Search took 0.10 seconds. Search: Posts Made By: J Franklin
Forum: Early V8 (1932-53) Today, 02:05 PM
Replies: 2
Views: 19
Posted By J Franklin
Re: 34 Pickup

The one you purchased will work fine on your pick-up.
Forum: Model A (1928-31) Yesterday, 10:40 AM
Replies: 12
Views: 306
Posted By J Franklin
Re: Front brake shoes grab

Nobody mentioned that grease or other contaminants on the linings or drum can cause this to happen, especially when first using the brakes.
Forum: Model A (1928-31) 06-07-2024, 01:24 AM
Replies: 7
Views: 401
Posted By J Franklin
Re: Wobbly dist—hard to disgnose/fix?

It must have a bent or stuck shaft. It shouldn't be an expensive fix.
Forum: Model A (1928-31) 06-05-2024, 10:59 PM
Replies: 10
Views: 648
Posted By J Franklin
Re: FB hotdog truck-2500.

Link?
Forum: Model A (1928-31) 06-04-2024, 05:22 PM
Replies: 6
Views: 290
Posted By J Franklin
Re: Blue Crown cross ref?

Your plug has a short reach compared to a model A plug.
Forum: Model A (1928-31) 06-02-2024, 04:46 PM
Replies: 8
Views: 487
Posted By J Franklin
Re: Gear Grind After Clutch Adjustment

1&1/2"-2" is good for free play. Look for a crack while depressing and releasing the clutch peddle. You don't want the clutch to not work comming to a stop at an intersection, or pulling into your...
Forum: Model A (1928-31) 06-02-2024, 10:50 AM
Replies: 21
Views: 916
Posted By J Franklin
Re: rod nuts...why the odd size?

It wasn't an odd size in 1928.
Forum: Model A (1928-31) 06-01-2024, 10:39 AM
Replies: 24
Views: 1,049
Posted By J Franklin
Re: Different length rear axle shaft threads on either side?

Maybe they were made by different manufacturers.
Forum: Model A (1928-31) 05-29-2024, 03:53 PM
Replies: 29
Views: 1,197
Posted By J Franklin
Re: help! clutch won‘t disengage…

Yes, with a crack things can move, but not enough to disengage the disk.
Forum: Model A (1928-31) 05-29-2024, 11:27 AM
Replies: 29
Views: 1,197
Posted By J Franklin
Re: help! clutch won‘t disengage…

Check for broken, or cracks in the linkage.
Forum: Early V8 (1932-53) 05-28-2024, 01:19 PM
Replies: 9
Views: 506
Posted By J Franklin
Re: Early ford oil pump id

My 1934 big truck has one like the first one.
Forum: Model A (1928-31) 05-27-2024, 06:38 PM
Replies: 10
Views: 521
Posted By J Franklin
Re: Transmission pops out of third gear

I remember they were .006. Did it pop out of gear for the last owner?
Forum: Model A (1928-31) 05-26-2024, 04:14 PM
Replies: 2
Views: 289
Posted By J Franklin
Re: Clutch Inspection Cover

No problem.
Forum: Model A (1928-31) 05-26-2024, 04:13 PM
Replies: 6
Views: 409
Posted By J Franklin
Re: Throw out bearing grease fitting

The throwout bearing most likely is the type that will not take grease and the fitting is only there to lube the bearing collar. Why not leave it as is and just give it a few drops of heavy oil now...
Forum: Model A (1928-31) 05-26-2024, 11:28 AM
Replies: 6
Views: 409
Posted By J Franklin
Re: Throw out bearing grease fitting

I have a pipe thread tap if you need one.
Forum: Model A (1928-31) 05-24-2024, 09:52 PM
Replies: 14
Views: 472
Posted By J Franklin
Re: installing grease baffle on front wheels Model AA truck

I see the part I couldn't figure out.
Forum: Model A (1928-31) 05-24-2024, 06:04 PM
Replies: 14
Views: 472
Posted By J Franklin
Re: installing grease baffle on front wheels Model AA truck

So the AA has a grease seal somewhere? It still looks (in photo) like the bearing is outside the baffle, and could still sling grease onto the brake lining. My model a doesn't have any grease seal in...
Forum: Model A (1928-31) 05-23-2024, 08:50 PM
Replies: 14
Views: 472
Posted By J Franklin
Re: installing grease baffle on front wheels Model AA truck

What I don't see in the photo is any baffle around the bearing, or is it part of the hub?
Forum: Model A (1928-31) 05-23-2024, 10:42 AM
Replies: 14
Views: 472
Posted By J Franklin
Re: installing grease baffle on front wheels Model AA truck

I believe the drawing is the correct application. On Bob C's photo, how does the baffle even function? It is inside of the slinging grease from the bearing.
Forum: Model A (1928-31) 05-22-2024, 03:11 PM
Replies: 16
Views: 1,079
Posted By J Franklin
Re: 1931 model a engine

Looks good to me also.
Forum: Model A (1928-31) 05-21-2024, 10:41 AM
Replies: 13
Views: 599
Posted By J Franklin
Re: 1931 Model A not turning over

Or the bendix is stuck. OOPS! I see you could turn it by hand.
Forum: Model A (1928-31) 05-21-2024, 12:50 AM
Replies: 11
Views: 674
Posted By J Franklin
Re: Babbit replacement

A shop did mine with what they called diesel tin babbit.
Forum: Model A (1928-31) 05-19-2024, 10:26 PM
Replies: 13
Views: 599
Posted By J Franklin
Re: 1931 Model A not turning over

Good idea!
Forum: Model A (1928-31) 05-19-2024, 10:16 PM
Replies: 13
Views: 599
Posted By J Franklin
Re: 1931 Model A not turning over

Does it turn over with the hand crank?
Forum: Model A (1928-31) 05-19-2024, 09:52 PM
Replies: 13
Views: 599
Posted By J Franklin
Re: 1931 Model A not turning over

Does it turn with your hand crank?
Showing results 1 to 25 of 500
Page 1 of 20 1 234511 Last »

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:07 PM.