Forum: Model A (1928-31)
Yesterday, 02:45 PM
|
Replies: 9
Views: 267
Re: rod nuts...why the odd size?
Last year I picked up 19/32” and 21/32” sockets off Amazon for very reasonable cost. Got into the engine and someone had already replaced those nuts with 5/8”. Go figure.
|
Forum: Model A (1928-31)
06-01-2024, 09:26 PM
|
Replies: 10
Views: 534
Re: Clutch chatter
Yup. When I purchased my ‘31 a couple of years ago it had ugly chatter. Upon examination I found one of the nuts on the bolt through the Float-a- Motor rubbers was about to fall off. That mount was...
|
Forum: Model A (1928-31)
06-01-2024, 09:38 AM
|
Replies: 17
Views: 586
|
Forum: Model A (1928-31)
05-31-2024, 07:27 PM
|
Replies: 17
Views: 586
|
Forum: Model A (1928-31)
05-31-2024, 04:49 PM
|
Replies: 6
Views: 452
|
Forum: Model A (1928-31)
05-31-2024, 11:07 AM
|
Replies: 15
Views: 614
Re: Which Side Mirror?
I also have a mirror on the right fender spare. I found when I put the seat back that I could not see the mirror, so I fabricated a longer stalk for it. Then I put a 4" fisheye lens...
|
Forum: Model A (1928-31)
05-31-2024, 10:56 AM
|
Replies: 15
Views: 614
Re: Which Side Mirror?
See attached. Snyders uses the Vintique number (A-17741-A), Mikes uses the same number without the dashes (A17741A), Bratton's uses a different number (24200), and Bert's uses yet a third number...
|
Forum: Model A (1928-31)
05-30-2024, 06:04 PM
|
Replies: 15
Views: 614
|
Forum: Model A (1928-31)
05-30-2024, 09:48 AM
|
Replies: 15
Views: 614
Re: Which Side Mirror?
I have the hinge mirrors on both sides of both of my sedans and love them (I had to mod one to fit the right side of the 31 slant). Not sure off the top of my head how the cabriolet door would differ...
|
Forum: Model A (1928-31)
05-29-2024, 07:29 AM
|
Replies: 19
Views: 1,002
Re: Shortened pitman arm
I acquired a shortened Pittman arm as part of a very weathered front suspension. The ball is quite badly pitted, and I can’t see installing it that way. Has anyone had any success filling badly...
|
Forum: Model A (1928-31)
05-28-2024, 06:44 AM
|
Replies: 15
Views: 571
|
Forum: Model A (1928-31)
05-27-2024, 10:38 AM
|
Replies: 6
Views: 336
Re: 1930 Fordor Wood
You never really know what you have until you tear it down. I got real lucky on my ‘30, what minimal dicey wood I have can be corrected with epoxy.
|
Forum: Model A (1928-31)
05-27-2024, 07:38 AM
|
Replies: 10
Views: 584
Re: Adjusting Brake Rods
There is also an aftermarket gizmo available from the vendors (https://www.snydersantiqueauto.com/product.htm?pid=977589&cat=41655) that attaches a spring to the motor mounts. I have Float-A-Motor...
|
Forum: Model A (1928-31)
05-27-2024, 07:31 AM
|
Replies: 6
Views: 336
Re: 1930 Fordor Wood
You can see the body cross members and the sill wood from underneath. Suggest a very thin probe to see if you can find rot. Another vulnerable place is the header, there might be a small opening at...
|
Forum: Model A (1928-31)
05-27-2024, 07:23 AM
|
Replies: 15
Views: 571
|
Forum: Model A (1928-31)
05-24-2024, 03:57 PM
|
Replies: 8
Views: 335
Re: Vicky front seats
There was an article in The Restorer a few months back about a guy who was reproducing them.
|
Forum: Model A (1928-31)
05-23-2024, 03:17 PM
|
Replies: 1
Views: 265
|
Forum: Model A (1928-31)
05-23-2024, 06:03 AM
|
Replies: 26
Views: 1,317
Re: Dropping the oil pan
I had an engine in the car and dropped the oil pan to clean out the moderate sludge, then did likewise for the valve chamber. When I disassembled the engine a year later I found the oil channel to...
|
Forum: Model A (1928-31)
05-23-2024, 05:55 AM
|
Replies: 8
Views: 648
Re: Edsel in a 28
Wasn’t the first one off the assembly line a roadster? And if so, could this be it?
|
Forum: Model A (1928-31)
05-22-2024, 06:06 PM
|
Replies: 16
Views: 1,038
Re: 1931 model a engine
Since you have the head off, this would be a good time to get a good straightedge and check the head and block for flatness. I use 0.002" as my standard. Check it with the straightedge going both...
|
Forum: Model A (1928-31)
05-22-2024, 11:58 AM
|
Replies: 10
Views: 511
|
Forum: Model A (1928-31)
05-22-2024, 11:52 AM
|
Replies: 17
Views: 892
Re: Rebuilt Engine Options
Anyone have a recommended source for the diaphragm clutch for a Model A? I have a Burtz flywheel that is drilled for a V-8 pressure plate.
|
Forum: Model A (1928-31)
05-21-2024, 01:06 PM
|
Replies: 7
Views: 512
|
Forum: Model A (1928-31)
05-21-2024, 10:30 AM
|
Replies: 51
Views: 2,496
Re: sign of the times
When I was in college (early 70’s) I had a Volvo sedan (long story) with a four speed. My girlfriend didn’t have a car, so I had to teach her to drive the four speed. She was game, did well, and her...
|
Forum: Model A (1928-31)
05-20-2024, 11:50 AM
|
Replies: 7
Views: 517
Re: Eaton gas cap, original or aftermarket?
Okra - I have not had good luck with repro 30/31 caps, they've either been too tight to rotate to seal (had to bend the tabs on the cap) or too loose to seal properly (had to fiddle with gaskets). As...
|