Forum: Early V8 (1932-53)
06-17-2024, 06:13 AM
|
Replies: 32
Views: 1,094
Re: Stop Lights 1940 Ford
Get a complete wiring harness from Tyree Harris or one of the several other suppliers be done with electrical wiring problems. Extra wires can be added for accessories like turn signals.
|
Forum: Early V8 (1932-53)
06-15-2024, 06:20 AM
|
Replies: 6
Views: 324
|
Forum: Early V8 (1932-53)
06-15-2024, 06:06 AM
|
Replies: 32
Views: 1,094
Re: Stop Lights 1940 Ford
No license plate light appears there is no power. Maybe dirty contact on the circuit breaker. For temporary test purpose, jumper the circuit breaker and see if you have lights.
|
Forum: Early V8 (1932-53)
06-13-2024, 07:01 AM
|
Replies: 30
Views: 1,282
|
Forum: Early V8 (1932-53)
06-13-2024, 06:03 AM
|
Replies: 32
Views: 1,094
Re: Stop Lights 1940 Ford
If you check the two wires at the stop light switch one is energized and the other not. It sounds as if the rear lights have lost their ground. If the license plate light is lit this will confirm...
|
Forum: Early V8 (1932-53)
06-10-2024, 10:27 AM
|
Replies: 9
Views: 336
Re: 59A Flathead Running Rich, Need Help
Are you using the gaskets for the power valves? They may be leaking. Have you checked float level? It's possible the accelerator pumps are supplying too much fuel. Is the accelerator link in the...
|
Forum: Early V8 (1932-53)
06-10-2024, 06:26 AM
|
Replies: 3
Views: 297
|
Forum: Early V8 (1932-53)
06-09-2024, 06:20 AM
|
Replies: 41
Views: 1,782
Re: Front Axle 1939 Ford pickup
The bolt is in the middle of the spring length and width, it functions to hold all the spring leafs together. It has a Zerk fitting on the bottom of the bolt for spring lubrication. The square head...
|
Forum: Early V8 (1932-53)
06-09-2024, 05:37 AM
|
Replies: 30
Views: 1,282
|
Forum: Early V8 (1932-53)
06-06-2024, 06:27 AM
|
Replies: 41
Views: 1,782
Re: Front Axle 1939 Ford pickup
The front spring has a square headed bolt in the center (about 3/8" tall head) that fits into a square hole in the front crossmember. This does not allow the spring pack to move left or right,...
|
Forum: Early V8 (1932-53)
06-04-2024, 07:34 AM
|
Replies: 27
Views: 1,508
Re: Anyone have one they can measure?
Below is another photo of the early 35 intake manifold with it's round hole under the fuel pump riser for the internal baffle tube. The baffle tube and the tube off the fuel pump riser are the...
|
Forum: Early V8 (1932-53)
06-04-2024, 07:11 AM
|
Replies: 17
Views: 423
Re: 39 synchronizer question
That is the 81A syncro hub and it should have three steel balls and springs. Mac sells a kit with the balls and springs for the syncro. The transmission has to come apart to install the kit. With...
|
Forum: Early V8 (1932-53)
06-03-2024, 07:00 AM
|
Replies: 27
Views: 1,508
Re: Anyone have one they can measure?
Although the shorter tube at 4-1/2" is the most popular they did come with the longer depending upon the intake manifold. The 35-36 restoration book explains the difference in the intake manifolds...
|
Forum: Early V8 (1932-53)
06-01-2024, 06:36 AM
|
Replies: 9
Views: 544
|
Forum: Early V8 (1932-53)
06-01-2024, 06:15 AM
|
Replies: 15
Views: 699
|
Forum: Early V8 (1932-53)
05-30-2024, 07:08 AM
|
Replies: 9
Views: 658
|
Forum: Early V8 (1932-53)
05-30-2024, 06:18 AM
|
Replies: 14
Views: 445
|
Forum: Early V8 (1932-53)
05-30-2024, 06:16 AM
|
Replies: 2
Views: 196
Re: 1947 Cluster Gear Endplay Opinion
0.010" steel shim stock cut like a washer and place between the case and the front thrust washer, cut the OD so it does not rotate. Appears the case is worn, if the case does not have flat thrust...
|
Forum: Early V8 (1932-53)
05-29-2024, 09:00 AM
|
Replies: 27
Views: 1,508
|
Forum: Early V8 (1932-53)
05-25-2024, 07:25 AM
|
Replies: 3
Views: 210
|
Forum: Early V8 (1932-53)
05-25-2024, 07:08 AM
|
Replies: 9
Views: 334
|
Forum: Early V8 (1932-53)
05-25-2024, 07:01 AM
|
Replies: 8
Views: 357
Re: three brush regulator
Suggest changing the operation of the two rate to be the same as the regular cutout. Just add the diode or you may be able to put the internals of a Fun Projects inside.
|
Forum: Early V8 (1932-53)
05-24-2024, 09:35 AM
|
Replies: 3
Views: 210
|
Forum: Early V8 (1932-53)
05-23-2024, 06:10 AM
|
Replies: 4
Views: 357
|
Forum: Early V8 (1932-53)
05-22-2024, 06:08 AM
|
Replies: 11
Views: 587
Re: 40 gearset in a 46 pu case
If you have a used 81A main shaft and want to use it I suggest pulling out the small locating pin and replacing it with a new pin.
|