|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-30-2017, 05:15 PM | #1 |
Senior Member
Join Date: Jan 2011
Location: Colorado Springs
Posts: 868
|
Hub seal orientation
I want to verify the rear hub seal (and rear inner axle seal) orientation before pressing them in.
I believe the seals are oriented with the metal spring toward the grease. My attached photo shows the outsides of the seals, oriented away from the grease, true? Can anyone confirm?
__________________
Ray White |
01-30-2017, 05:27 PM | #2 |
Senior Member
Join Date: Jan 2017
Location: Maryhill Ont Canada
Posts: 834
|
Re: Hub seal orientation
That's how I mount them.
|
Sponsored Links (Register now to hide all advertisements) |
|
01-30-2017, 05:33 PM | #3 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,754
|
Re: Hub seal orientation
I'll save myself a thousand words.
Bob |
01-30-2017, 06:30 PM | #4 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 3,131
|
Re: Hub seal orientation
The original inner hub seals were made of leather. One of Fords suppliers was Chicago Rawhide. Quite often the original seals are found still in place during an overhaul. The letters CR are found stamped on the side. Most of the leather is usually deteriorated.
It made sense to install them such that when the axle slid into place it did not fold the leather back on itself. Modern replacement seals are made of neoprene. Supplier's literature say to face the taper on the seal toward the lubricant. There is a taper on both sides of the seal and it is not specified what lubricant they are talking about, the oil in the banjo or the grease that is pumped into the rear wheel bearing. The seal is a grease seal, not an oil seal. Its purpose is to prevent the grease that is pumped in through the grease fitting on the rear backing plate from migrating down the axle shaft toward the differential instead of going outboard to the rear wheel bearing. People continue to argue about the purpose of the seal and which direction to face it. If you have ever pulled a rear end apart that had the original shot seals installed and an owner who religiously pumped grease into the grease fitting on the backing plate you would find that grease has centrifuged around the axle an inch thick and is as long toward the differential as the owner's frequency of pumping grease into it. I don't think it matters which direction you face the seal, either way it will snap into the slight groove in the axle and it will do the job. It is best to pack the rear wheel bearings when you have the drum off and forget about that grease fitting. Ford eliminated it during the early V8 years. Tom Endy |
02-09-2020, 11:37 AM | #5 |
Junior Member
Join Date: Jan 2015
Posts: 6
|
Re: Hub seal orientation
Newbie here so I put what I call the open end toward the bearing that I greased ,CORRECT? It seams that the grease would eventually fill the opening that is in the seal side with the spring in it ???? WOW.
|
02-09-2020, 11:51 AM | #6 |
Senior Member
Join Date: Oct 2019
Location: Washington
Posts: 175
|
Re: Hub seal orientation
Sponsored Links (Register now to hide all advertisements)
|
02-09-2020, 11:53 AM | #7 |
Senior Member
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,089
|
Re: Hub seal orientation
stengel, correct, the seals are to keep the grease in the wheel bearing.
|
02-09-2020, 01:06 PM | #8 |
Senior Member
Join Date: May 2010
Location: Portland OR
Posts: 6,342
|
Re: Hub seal orientation
I put mine on so any part that slides into or onto you don't have to fight the taper in the seal so the open side is to the grease not away. When grease is added, you want the lip to be pushed to seal, not pushed to open and allow the grease past.
__________________
I know the voices aren't real but damn they have some good ideas! |
|
|
Sponsored Links (Register now to hide all advertisements) |
|