|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-28-2017, 02:28 PM | #1 |
Senior Member
Join Date: Jul 2014
Location: NW Pa./Sc.
Posts: 252
|
Just received my EVR from Fun Projects
I have a 6 volt pos. ground system. The instructions that came with the EVR say to loosen the 3rd brush nut to adjust the brush and then to retighten the nut. I moved my 3rd brush to the top (min output) without loosening anything. Obviously, I did not tighten it. What am I missing here? I sure don't want to start a fire or destroy a $64 EVR. I wanted to ask this before I installed the new EVR. Thanks as always.
Last edited by smittykid; 08-28-2017 at 02:29 PM. Reason: spelling |
08-28-2017, 02:43 PM | #2 |
Senior Member
Join Date: Jun 2017
Location: Walla Walla, WA
Posts: 1,047
|
Re: Just received my EVR from Fun Projects
I think yours is like mine where there is no nut to loosen.
|
Sponsored Links (Register now to hide all advertisements) |
|
08-28-2017, 02:55 PM | #3 |
Senior Member
Join Date: May 2010
Location: Rhode Island
Posts: 649
|
Re: Just received my EVR from Fun Projects
I just installed one few weeks ago. Most generators do not have a nut to tighten, there's a small internal spring finger that provides friction and prevents the brush ring from slipping on its own. Maybe the powerhouse style uses a locking nut?
The EVR works great by the way! |
08-28-2017, 03:02 PM | #4 | |
Senior Member
Join Date: Jul 2014
Location: NW Pa./Sc.
Posts: 252
|
Re: Just received my EVR from Fun Projects
Quote:
|
|
08-28-2017, 03:03 PM | #5 |
Senior Member
Join Date: Jul 2014
Location: NW Pa./Sc.
Posts: 252
|
Re: Just received my EVR from Fun Projects
|
08-28-2017, 03:18 PM | #6 |
Senior Member
Join Date: May 2010
Location: Cape Cod
Posts: 1,128
|
Re: Just received my EVR from Fun Projects
Sponsored Links (Register now to hide all advertisements)
For the fun products device, should you set it for the Minimum or Maximum Output ? Common sense would be to set it for the maximum and then have it regulate to the amount needed. Marc |
08-28-2017, 07:28 PM | #7 |
Senior Member
Join Date: May 2010
Location: Rhode Island
Posts: 649
|
Re: Just received my EVR from Fun Projects
The maker recommends 8 amps maximum output. Any more and you risk damaging the regulator.
|
08-28-2017, 07:40 PM | #8 | |
Senior Member
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,580
|
Re: Just received my EVR from Fun Projects
Quote:
Yes, follow the instructions...they work great.. .
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62 |
|
08-28-2017, 09:56 PM | #9 |
Senior Member
Join Date: May 2010
Location: North Carolina
Posts: 419
|
Re: Just received my EVR from Fun Projects
I have a new Fun Products EVR that I cannot install because I do not have the original style post on the generator. If the post has been replace with a wire coming out of the case, there is no way to attach it to the EVR. Works with original post only.
W. Michael |
08-28-2017, 10:32 PM | #10 |
Senior Member
Join Date: Aug 2011
Location: Eagle Bend, MN
Posts: 2,027
|
Re: Just received my EVR from Fun Projects
I set the output of the generator with an in line ammeter for 12 amps, before installing the EVR. I then swapped out the cutout for my new EVR. It has worked great for 5 years now. The ammeter on the dash is not an accurate method of setting the generator output.
__________________
"There are some that can destroy an anvil with a teaspoon and shouldn't be allowed to touch anything resembling a tool." |
08-28-2017, 10:51 PM | #11 | |
Senior Member
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,580
|
Re: Just received my EVR from Fun Projects
Quote:
http://www.funprojects.com/pdf/10505R6.PDF I also had a generator with no output stud, just a wire...but they are available and not too difficult to install. Neither of my two generators(one spare) have the lock nut on the third brush... .
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62 |
|
08-28-2017, 11:37 PM | #12 | |
Senior Member
Join Date: Jun 2017
Location: Walla Walla, WA
Posts: 1,047
|
Re: Just received my EVR from Fun Projects
Quote:
|
|
08-29-2017, 05:13 AM | #13 | |
Senior Member
Join Date: Jul 2014
Location: NW Pa./Sc.
Posts: 252
|
Re: Just received my EVR from Fun Projects
Quote:
In the instructions in bold print it says, "Only the generator 3rd brush assembly will be adjusted and under no circumstances should the 3rd brush assembly be set for more than 15 amps of charge". Hope this helps. Smitty |
|
08-29-2017, 06:28 AM | #14 |
Senior Member
Join Date: May 2010
Posts: 2,606
|
Re: Just received my EVR from Fun Projects
There is a possibility of some confusion here.
The 6 volt model supplies 15 amps. The 12 volt model supplies 8 amps. 1. If instructions say 8 amps then directions are for the 12 volt regulator. 2. If 15 amps the direction sheet is for the 6 volt version. If you set 12 volt regulator for 15 amps it will be damaged. If you set 6 volt regulator for 8 amps the battery might not get fully charged if you use the headlights. 3. Also if you flash the generator with regulator installed with either version, damage will occur. Last edited by Benson; 08-29-2017 at 08:25 AM. |
08-29-2017, 08:15 AM | #15 |
Senior Member
Join Date: May 2010
Location: Rhode Island
Posts: 649
|
Re: Just received my EVR from Fun Projects
Sorry for the confusion, I have the 12 volt model which us limited to 8 amps. I didn't realize the 6 volt model was different.
|
08-29-2017, 01:08 PM | #16 |
Senior Member
Join Date: May 2010
Location: Cape Cod
Posts: 1,128
|
Re: Just received my EVR from Fun Projects
Group,
I didn't realize that the limit was 15 amps. This device is a "shunt" regulator meaning that it shorts out the generator for a variable amount of time depending on the needed current for the car. For example, if 15 amps is needed, then the device doesn't do anything. If 1 amp is needed, then it shorts out the generator for almost all the time. The type that Tom W makes is a different design. His controls the actual output from the generator to provide the needed current by varying the current to the field coil to vary the output. Thus, if you need more, it makes more. Both work, but I like Tom W's better. Marc |
|
|
Sponsored Links (Register now to hide all advertisements) |
|