|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-18-2020, 01:49 AM | #1 |
Senior Member
Join Date: May 2010
Location: (Not far enough...) Outside of DC
Posts: 3,387
|
Whizzernick's Wicked Lift?
Hi Everyone. Can someone please school me about the lift we're seeing in this recent post by Whizzernick?
__________________
-Jeff H Have you thought about supporting the Early Ford V-8 Foundation Museum? |
01-18-2020, 05:43 AM | #2 |
Senior Member
Join Date: May 2010
Location: FP, NJ
Posts: 2,770
|
Re: Whizzernick's Wicked Lift?
In my youth, I worked at my neighbor's shop and they had what was called a "Bay Lift." It was an air operated devise with two long arms. The arms had nice big "cradles" at the ends. One had to only roll the lift under one end or the other of a car, put a little air in the cylinder to slowly lift the arms until the car's axle was sitting in the cradles and then give it a good blast and that end of the car would be three or four feet in the air. It was a lot nicer than lifting it with a floor jack and jack stands. In this photo, someone has TWO bay lifts.
__________________
Don't never get rid of nuthin! |
Sponsored Links (Register now to hide all advertisements) |
|
01-18-2020, 07:15 AM | #3 |
Senior Member
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
|
Re: Whizzernick's Wicked Lift?
Used to use one back in the late '50's in the body shop but never considered using two to lift the whole car off the ground. (score one for improvisation )
But, don't think I would try it outdoors in windy conditions!
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES Last edited by 51 MERC-CT; 01-18-2020 at 08:13 AM. |
01-18-2020, 01:22 PM | #4 |
Senior Member
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,935
|
Re: Whizzernick's Wicked Lift?
Clever? For sure, but too risky. Even for me.....
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson) |
01-18-2020, 01:25 PM | #5 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,319
|
Re: Whizzernick's Wicked Lift?
The first thing I thought when I opened the original was "Please, don't drop it!".
Last edited by tubman; 01-18-2020 at 01:46 PM. |
01-18-2020, 01:39 PM | #6 |
Senior Member
Join Date: May 2010
Location: FP, NJ
Posts: 2,770
|
Re: Whizzernick's Wicked Lift?
Sponsored Links (Register now to hide all advertisements)
__________________
Don't never get rid of nuthin! |
01-18-2020, 01:47 PM | #7 |
Senior Member
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
|
Re: Whizzernick's Wicked Lift?
On a perfectly leveled slab of concrete it may work just fine...but since Murre`s law says Murphy was a damn optimist...to many variables that can go wrong...
Very cool lift though...still have a mechanical ratchet jack with like a 6ft handle on it...very enviromental friendly no chances of oil leakes...takes a well sized wrestler to lift anything heavy on it... |
01-18-2020, 02:34 PM | #8 |
Senior Member
Join Date: Dec 2014
Location: Fort dodge, Iowa
Posts: 823
|
Re: Whizzernick's Wicked Lift?
I had an older friend that had an identical jack in his repair shop. It had an automatic safety stop that was spring loaded and as you raised the jack, it would snap into stops for different heights. If you raised to the desired height and did not lower to the last stop you could get a "surprise". This particular jack would leak a little air and there would be a sudden drop to the last safety stop. A young friend of mine had raised the jack quite high without letting the jack relax to the stop. An older experienced mechanic was underneath when the car dropped a couple inches to the last stop. It made a bang and I have never seen anyone get out from underneath a car that fast. Needless to say he heard a few choice words!
|
01-18-2020, 03:09 PM | #9 |
Senior Member
Join Date: Jul 2013
Location: Hayward Ca
Posts: 635
|
Re: Whizzernick's Wicked Lift?
Yes : my lifts are cool . I have 3 one is a bay lift one is a blackhawk (5000 lb )
and an (END LIFT ) I think. In picture the bay lift is in front blackhawk in rear. I use them in side ( most of the time ) The best part is you can go to exact the height you want real fast and you have access to most of the car. (CAUTION --- I DO NOT leave the cars in high position when not there ) mid position is ok 2-3 ft off floor |
01-18-2020, 03:16 PM | #10 | |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,113
|
Re: Whizzernick's Wicked Lift?
Quote:
Have you ever thought about what that car's gonna do when California begins a shakin'? DD |
|
01-18-2020, 05:14 PM | #11 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,436
|
Re: Whizzernick's Wicked Lift?
A person needs to make sure they can roll while lifting. They don't actually lift straight up like the old pneumatic bumper jacks did. I used to see those being used on both ends but the bumpers turned plastic and the post lifts made them obsolete.
If the ground isn't level enough, it could start rolling down hill. |
01-18-2020, 11:23 PM | #12 |
Senior Member
Join Date: May 2010
Location: Palmer, Alaska
Posts: 1,575
|
Re: Whizzernick's Wicked Lift?
Yes, they are 2 separate lifts. I used them when I worked for the local GM dealer back in the mid '70's. wish I had one.
|
01-19-2020, 12:52 AM | #13 |
Senior Member
Join Date: Sep 2016
Location: sydney australia
Posts: 1,034
|
Re: Whizzernick's Wicked Lift?
temp fate long enough and you know how its going to end but still, cool tool
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|