|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-07-2021, 07:46 PM | #1 |
Senior Member
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,897
|
Failed Experiment
If you never make mistakes you are not trying anything new.
One of the neat things that the engineers did at Ford was to design the intake and exhaust manifolds to be bolted together to transfer heat to the intake charge. This helps atomize the gasoline which was more important in 1928 than it is today. The Weber carburetor on my engine has an aluminum manifold and is kind of cold blooded. It takes a while to warm up and operate correctly. So, I thought, why not insert a 1/4 inch copper plate between the exhaust manifold and the aluminum intake manifole. I filed the back side of the aluminum manifold to get about 0.005 inch clearance between the intake manifold and copper plate and used counter sunk screws to attach the copper to the exhaust manifold, see photo below. Well. it worked too well. With my IR temperature gun, I measured 375 F on the outside of the intake manifold while the normal temperature, when warmed up is about 150. So off came the copper. I now just let the engine warm up a little longer before driving off.
__________________
A is for apple, green as the sky. Step on the gas, for tomorrow I die. Forget the brakes, they really don't work. The clutch always sticks, and starts with a jerk. My car grows red hair, and flies through the air. Driving's a blast, a blast from the past. |
02-07-2021, 08:01 PM | #2 |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,354
|
Re: Failed Experiment
Seems like in theory you could remove progressively more copper by drilling holes in the spacer until you got the conductivity you wanted. Would be a lot of trial and error though.
|
Sponsored Links (Register now to hide all advertisements) |
|
02-07-2021, 08:07 PM | #3 | |
Senior Member
Join Date: Aug 2019
Location: Hagerstown MD
Posts: 224
|
Re: Failed Experiment
Quote:
__________________
Building a '29 Speedster, the hard way... |
|
02-07-2021, 08:51 PM | #4 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,906
|
Re: Failed Experiment
Somehow your story brings the tale of The Sorcerer’s Apprentice” to mind.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
02-07-2021, 09:02 PM | #5 | |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Failed Experiment
Quote:
A while ago, I was talking with a guy in NZ as we looked at his car and he had welded an aluminium box under the manifold and run hot water from the top hose through it. Not only did the carburettor not ice up but he was able to come down a jet size and got better economy.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
|
02-07-2021, 11:05 PM | #6 | |
Senior Member
Join Date: May 2010
Location: PASADENA, CA
Posts: 1,884
|
Re: Failed Experiment
Sponsored Links (Register now to hide all advertisements)
Quote:
Chris W. Last edited by CWPASADENA; 02-07-2021 at 11:06 PM. Reason: TYPO |
|
02-07-2021, 11:08 PM | #7 |
Senior Member
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,897
|
Re: Failed Experiment
Rancho, Timing is not retarded. I was running at a fairly fast clip, more than an idle. I am also wondering if there was a closed loop: hotter intake leading to hotter exhaust leading to hotter intake.
Synchro, Thanks for correcting me, vaporizing. I thought there was a lot more heavy components in the gasoline of 1928, or maybe I was thinking 1915. I know Ford had to lower the compression ratio of the Model T because of the quality of the fuel and kept it fairly low for the Model A. Or maybe that was the octane rating. In my automotive engineering class in college we distilled gasoline which left a heavy brown tar after the lighter parts vaporized. Quite a range of the size of the molecules, each vaporizing at a different temperature. This was in the 1960's so gasoline has probably changed. The hot coolant from the engine would be a better solution as the temperature is more or less controlled and limited.
__________________
A is for apple, green as the sky. Step on the gas, for tomorrow I die. Forget the brakes, they really don't work. The clutch always sticks, and starts with a jerk. My car grows red hair, and flies through the air. Driving's a blast, a blast from the past. |
02-08-2021, 09:36 AM | #8 |
Senior Member
Join Date: Jun 2020
Location: Fall Creek, WI
Posts: 213
|
Re: Failed Experiment
Mistakes? I’m not familiar with the concept!
|
02-08-2021, 11:20 AM | #9 |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,046
|
Re: Failed Experiment
How about mounting that copper plate w/only one fastener in one corner. Then hook up a pull cable so you could manually pull-push the copper in or out to adjust the amount of heat going to the intake manifold.
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
02-08-2021, 12:11 PM | #10 |
Senior Member
Join Date: Jul 2010
Location: Pennsylvania
Posts: 1,100
|
Re: Failed Experiment
Interesting thoughts in this thread. Not to hijack it, but to add to the conversation, for the standard Zenith carb arrangement, do we really need that heat transfer feature of the exhaust/intake manifold nowadays, with the better fuels we have? As nkaminar said, the intent was to heat up the intake manifold so poor, low octane fuels of the late '20s would atomize. But with modern fuels that just love to vapor lock in the hot weather, would it be better to insulate the intake from the exhaust manifold?
|
02-08-2021, 01:30 PM | #11 |
Senior Member
Join Date: May 2010
Location: Ames, Iowa
Posts: 133
|
Re: Failed Experiment
Great Post! I will be waiting to see what you do next! One of my favorite quotes below!
“There are no failures – just experiences and your reactions to them.” – Tom Krause
__________________
Some is not a number... Soon is not a time... and hope is not a plan. |
02-08-2021, 02:35 PM | #12 | |
Senior Member
Join Date: Dec 2010
Location: Kritter Krick, Flaw-duh
Posts: 1,158
|
Re: Failed Experiment
Quote:
Henry Ford had the same attitude, “Failure is simply the opportunity to begin again, this time more intelligently.” |
|
02-08-2021, 02:43 PM | #13 | |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,354
|
Re: Failed Experiment
Quote:
|
|
02-08-2021, 03:21 PM | #14 | |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Failed Experiment
Quote:
Now, let's establish one thing that many have difficulty understanding. Petrol (gas) does not burn but its vapour does. If you submerge a spark plug in petrol and discharge it, nothing will happen (no oxygen) but do that in the vapour and the result is quite different. The carburettor atomises the fuel into small droplets which enter the manifold on their way to the cylinder. If the manifold is cold, the droplets do not turn to a vapour and therefore do not burn properly. The more volatile hydrocarbons vaporise quite easily (sometimes too easily, causing vapour lock) while the heavier ones do not. If the inlet manifold is heated, more of the heavy elements will vaporise and if they all do, you have complete combustion. If the inlet is not hot enough and some of the heavier ones do not vaporise, the engine runs lean. There is enough oxygen in there for complete combustion but the un vaporised heavy elements do not burn, meaning the engine is lean. The bind is, if the induction route is hot enough to vaporise the heavy elements, it is likely hot enough to cause trouble with the volatile ones boiling in the carburettor. Modern cars are designed to handle this but our cars were made for a different fuel. Different! - better in some ways, not as good as modern fuel in others. The octane was not as high as modern fuel but octane has nothing to do with any of this. Contrary to common belief, high octane fuel burns slower than low octane.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
|
02-08-2021, 03:38 PM | #15 |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,354
|
Re: Failed Experiment
Good article on the physics of vaporization:
https://www.hemmings.com/stories/art...t-now-you-dont |
02-08-2021, 07:25 PM | #16 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Failed Experiment
Quote:
I enjoyed that article. Thanks for posting. Sent from my iPhone using Tapatalk |
|
02-13-2021, 12:51 AM | #17 |
Senior Member
Join Date: May 2010
Location: Camarillo, CA and Pine Grove, CA
Posts: 2,832
|
Re: Failed Experiment
Using the choke to keep it running smooth until warmed up is certainly not a new concept. A cooler intake keeps the fuel cooler. Cooler fuel, like any liquid, shrinks when cool and expands with heat. Cooler fuel puts a bigger charge into your cylinder equaling more power. Many racers have their fuel line go through a container of dry ice just before entering the carburetor.
__________________
1921 Runabout 1930 Tudor Early 1930 AA Speed costs money. How fast do you want to go? |
02-13-2021, 03:37 PM | #18 |
Senior Member
Join Date: Jan 2018
Location: Tocumwal, NSW, Australia
Posts: 1,748
|
Re: Failed Experiment
I ran radial engines in my aeroplanes for years. The first rebuilt exchange I purchased came without a carburettor gasket so I made one. I later learned they aren’t used because the conduct of heat from the engine to the carb eliminates icing so I removed it. In addition, carburated engines have a control to induce hot air into the carb to stop ice or eliminate what has already formed.
The induced engine heat (because of no carb gasket) was only a problem on one occasion. A day when fire bombing in extreme heat. Whilst on the ground reloading, the fuel in the carby just got too hot. When I’d open the throttle it would cough and blow black unburned fuel from the exhaust until the hot fuel in the carb was refreshed with cool fuel, then normal operation resumed. I once had a 4-cylinder ute and figured if I could make the intake air cooler I’d get even better economy, so I modified it. Carb ice drove me mad. The engine would run badly until it snuffed out. It did run normally but only if it reached operation temperature. I returned the system to “as designed”. Whilst I haven’t modified a fuel system since I do agree with nkaminar Who says, and I quote If you never make mistakes you are not trying anything new.
__________________
I know many things, But I don't know everything, Sometimes I forget things. And there are times when I have a long memory. |
02-13-2021, 11:02 PM | #19 |
Senior Member
Join Date: May 2010
Location: PASADENA, CA
Posts: 1,884
|
Re: Failed Experiment
Charles Lindberg almost lost the Spirit of St Louis when flying from San Diego to New York to start his non stop flight to Paris. He was crossing the Rocky Mountains and flying the plane at this high of an altitude for the first time and the carburetor started to ice up. The engine was running rough and he keep loosing altitude, but was finally able to get down low enough without hitting a mountain that the warmer air melted the ice and the engine picked up power. At a stop in St Louis, a system to heat the incoming air to the carburetor was installed before he proceeded on to New York.
Carburetor heat is necessary and most modern production automobiles with carburetors had provisions to either heat the air before it entered the carburetor or heat the actual carburetor itself or both. I do not think Model A's had a big problem with the carburetor actually icing up because the air that entered the carburetor was warmed by the exhaust manifold and muffler head pipe. Heat transferred from the exhaust manifold to the intake manifold helped with fuel vaporization. Chris W. Last edited by CWPASADENA; 02-13-2021 at 11:06 PM. Reason: CLARIFICATION |
02-14-2021, 11:28 AM | #20 | |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,046
|
Re: Failed Experiment
Quote:
See: https://www.hemmings.com/stories/article/all-rise
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|