|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-28-2014, 05:32 PM | #1 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
License plate mount for 32 spreader bar?
Does anyone make a mount that is not billet crap? Looking to put one on my AV8 and don't want to cover up the grill. I'm thinking I could hang it down off the spreader bar.
|
09-28-2014, 07:04 PM | #2 |
Senior Member
Join Date: May 2010
Location: Illinois
Posts: 2,185
|
Re: License plate mount for 32 spreader bar?
|
Sponsored Links (Register now to hide all advertisements) |
|
09-28-2014, 07:21 PM | #3 |
Member Emeritus
Join Date: May 2010
Location: Madison, NJ
Posts: 5,230
|
Re: License plate mount for 32 spreader bar?
Look at Neals brackets in the HAMB thread...they are sort of a shortened version of the early '32 brackets, and if you need a head start on making them there are commercially made muffler clamps very like that...also available as parts brackets for motorcycles.
You want to lower the thing greatly, I assume, and something like that could hang the plate overlapping the front bar and as low as you care to go. Anything other than stock will leave you without ready access to the hand crank, but should be readily removable so you don't have to call AAA like a soccer mom when your battery dies. |
09-28-2014, 08:24 PM | #4 |
Member
Join Date: Jul 2014
Location: Black hawk S.Dakota
Posts: 32
|
Re: License plate mount for 32 spreader bar?
I welded 2 stainless steel tabs on mine then drilled and tapped.
|
09-28-2014, 09:18 PM | #5 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: License plate mount for 32 spreader bar?
Nice info from the HAMB, I think I'll do something like that,
Thanks guys! My AV8 is built more like a early 50's car, so this should fit right in. |
09-28-2014, 09:29 PM | #6 |
Senior Member
Join Date: May 2010
Location: Capital of Corruption , NY
Posts: 811
|
Re: License plate mount for 32 spreader bar?
Sponsored Links (Register now to hide all advertisements)
|
09-29-2014, 12:52 AM | #7 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: License plate mount for 32 spreader bar?
Tony,
That's simple and looks good as well. |
09-29-2014, 08:07 AM | #8 |
Senior Member
Join Date: May 2010
Posts: 4,489
|
Re: License plate mount for 32 spreader bar?
I have done it with a piece of ss sheet the size of the plate with a 1.5 inch lip at a 45 degree angle and bolted the plate behind the spreader into the bottom. I've done this on several highboys as Nebraska requires a front plate.
|
09-29-2014, 09:40 AM | #9 |
Senior Member
Join Date: Oct 2010
Location: North Pole, Alaska
Posts: 1,470
|
Re: License plate mount for 32 spreader bar?
Alaska requires one too, is the spreader heavy enough to drill and tap? Mines aftermarket chrome, so I'm assuming it's very thin.
|
09-29-2014, 12:52 PM | #10 |
Member Emeritus
Join Date: May 2010
Location: Madison, NJ
Posts: 5,230
|
Re: License plate mount for 32 spreader bar?
Originals are quite thick metal, since Ford considered them a structural part of frame. Plenty there to hold a license bolt.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|