|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-08-2022, 08:08 AM | #1 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,754
|
Time to Bore an 8BA Flathead! Vintage Buma Boring Action! + Helicoil!
In this week's video I show how I go about using the vintage Buma boring machine on an 8BA flathead block. Also this week I repair a head stud hole using a heli coil. I hope you find it interesting. Thanks for joining me once again in Mart's Garage.
Mart. https://youtu.be/Jmj850KePH4 |
07-08-2022, 10:39 AM | #2 |
Senior Member
Join Date: Feb 2020
Location: Paducah Ky
Posts: 279
|
Re: Time to Bore an 8BA Flathead! Vintage Buma Boring Action! + Helicoil!
Hi Mart, great job as usual on the boring job.
Al Hook |
Sponsored Links (Register now to hide all advertisements) |
|
07-08-2022, 10:49 AM | #3 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,944
|
Re: Time to Bore an 8BA Flathead! Vintage Buma Boring Action! + Helicoil!
Mart:
THANK YOU very much for making such a detailed video explaining every aspect that a novice needs to know. Your "self-taught" problem solving skills are really appreciated as such knowledge is not written down in any book. It is a wonderful video. Perhaps I am missing something but, I am wondering how your boring machine is attached (bolted?) to the bare block. I remember in 1967 I had an 8BA bored with a similar machine and the cost was $5 per cylinder. I was making $1.15 per hour. PLEASE keep sharing your knowledge. |
07-08-2022, 11:30 AM | #4 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,754
|
Re: Time to Bore an 8BA Flathead! Vintage Buma Boring Action! + Helicoil!
Thanks fellas.
Fordy: In my case I have 2 12mm long studs down the two adjacent bores. There is a cross bar top and bottom. You can see the bottom of one of the clamping bars when I show the boring bar exiting the bore. All my tooling is home made as my machine came with no tooling. I was lucky to find the correct micrometer separately. |
07-08-2022, 12:33 PM | #5 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,944
|
Re: Time to Bore an 8BA Flathead! Vintage Buma Boring Action! + Helicoil!
Thanks for the reply Mart. Yes, I bet it's difficult to find a boring machine like yours that still has the special micrometer.
|
07-08-2022, 02:57 PM | #6 |
Senior Member
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,040
|
Re: Time to Bore an 8BA Flathead! Vintage Buma Boring Action! + Helicoil!
Sponsored Links (Register now to hide all advertisements)
|
07-08-2022, 05:17 PM | #7 |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,194
|
Re: Time to Bore an 8BA Flathead! Vintage Buma Boring Action! + Helicoil!
|
07-09-2022, 03:08 AM | #8 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,754
|
Re: Time to Bore an 8BA Flathead! Vintage Buma Boring Action! + Helicoil!
Ha ha thanks fellas.
Mart. |
07-09-2022, 06:59 AM | #9 |
Senior Member
Join Date: Aug 2017
Location: ohio
Posts: 986
|
Re: Time to Bore an 8BA Flathead! Vintage Buma Boring Action! + Helicoil!
Another good one. Thanks Mart ! Cheers ...
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|