|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-27-2021, 05:08 PM | #21 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,390
|
Re: Vintage Precision Hub Puller
People have been hitting the pullers with a hammer since the cars were new. Not going to hurt anything. JMO
Paul in CT |
05-27-2021, 06:04 PM | #22 |
Senior Member
Join Date: May 2010
Location: Wa.
Posts: 5,409
|
Re: Vintage Precision Hub Puller
Pullers that pull on the studs are an EXTREMELY poor choice for the job.
An explanation should not be required. When axles are lapped to the hubs as in vintage race cars, they are almost impossible to get off by simply applying force no matter what type or brand of puller is used, however they normally come off with no more that 75 lb of torque simply by heating the hub to about 300 degrees after torque is applied. This will not affect the heat treat in the hub or axle. |
Sponsored Links (Register now to hide all advertisements) |
|
05-27-2021, 06:28 PM | #23 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,906
|
Re: Vintage Precision Hub Puller
I torque those rear hub nuts to 100 fp.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
05-27-2021, 06:51 PM | #24 | |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,497
|
Re: Vintage Precision Hub Puller
Quote:
While trying to get something happening, I found that the American NPT threads are not used anywhere else so why supply them with American threads? That is about $170 wasted. The set up is so wonderful, I have to go back to the thermostat in the hose. Buy one of their hub pullers? Not bleedin likely!
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
|
05-27-2021, 07:21 PM | #25 |
Senior Member
Join Date: Jul 2010
Location: Livonia, MI
Posts: 197
|
Re: Vintage Precision Hub Puller
I have a '41 Ford in addition to my Model As. I bought the Vintage Precision puller when I had to do a brake job on that car.
I am impressed with the pullers construction and will not hesitate to use it on my older cars. I also like the plastic telescope it comes shipped in. It's great for storing the puller on the shelf. |
05-27-2021, 07:29 PM | #26 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Vintage Precision Hub Puller
Sponsored Links (Register now to hide all advertisements)
Quote:
Hmmm.... I bought one a while back, and the temperature probe fits fine. I’m very happy with my unit. I don’t know why yours would be so different from mine. Sent from my iPhone using Tapatalk |
|
05-27-2021, 07:45 PM | #27 | |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,497
|
Re: Vintage Precision Hub Puller
Quote:
Once bitten, twice shy!
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
|
05-27-2021, 08:15 PM | #28 | |
Senior Member
Join Date: Sep 2014
Posts: 521
|
Re: Vintage Precision Hub Puller
Quote:
|
|
05-27-2021, 08:18 PM | #29 |
Senior Member
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
|
Re: Vintage Precision Hub Puller
To answer the op's question, The Vintage precision puller is a fine unit that works great for me. Pricey, but worth it.
|
05-27-2021, 08:33 PM | #30 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Vintage Precision Hub Puller
Quote:
I bought a Stewart Warner temperature gauge from Speedway Motors. It’s a bit pricey, but it works great. No regrets. https://www.speedwaymotors.com/Stewa...Inch,7150.html Hmmm... Now that I think about it, I think I originally bought a cheap China-made temperature gauge that didn’t fit. However, like I said, the Stewart Warner gauge works great for me, and it looks period correct. Sent from my iPhone using Tapatalk Last edited by shew01; 05-27-2021 at 08:38 PM. |
|
05-27-2021, 11:41 PM | #31 |
Senior Member
Join Date: May 2010
Location: midlothian illinois
Posts: 447
|
Re: Vintage Precision Hub Puller
I also bought one of the Vintage hub pullers and have used it on my A', my friends A' on more than one occasion, several spare rear ends , my 34 coupe, and also a 40 rear end. I have yet to encounter any problems removing the hubs, although some have been very tight and I also use a good quality 3/4" SK breaker bar and their sockets or an impact socket on the bar for greater leverage. I will add this one note for my disassembly procedure. Before installing the hub puller I use a sledge hammer on one side of the hub @ the taper, and a large ball peen hammer struck on the opposite side of the hub against the shanks stem. This additional effort does seem to relieve the grip of the most stubborn hubs - even ones that were rusted to the axle.
Yes it was expensive for a very specific tool that will only be used a few times, but without it, or something at least equal to it in quality and performance, you could be spending a lot more time removing the hubs than need be - hopefully successful. |
05-28-2021, 12:10 AM | #32 |
Senior Member
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,849
|
Re: Vintage Precision Hub Puller
While the Vintage Precision puller looks like a nice unit, it can only be used on one type of hub (per their website. The Mitchell puller can be used on both types of hubs. I have run into cars with both types of hubs. https://mitchelloverdrives.com/mitchell-hub-puller/ less expensive too.
|
05-28-2021, 04:25 AM | #33 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: Vintage Precision Hub Puller
Quote:
My car has both types of hubs. Sent from my iPhone using Tapatalk |
|
05-28-2021, 06:24 AM | #35 |
Senior Member
Join Date: May 2010
Posts: 1,304
|
Re: Vintage Precision Hub Puller
I have not seen this type of hub puller in the USA, swap meets etc etc . Someone has cut slots to use it on a bigger lug nut spacing . It seems to be forged steel . It has a heavy outer nut with a sliding inner nut . Wind the big one up hard and bop the inner . Works a treat even on a correctly fitted hub . I am aware that in extreme cases the hub flange could be distorted but up to now that has not happened . I sometimes use heat on the hub if I think I could cause that problem . It is made by HARTRO which think could be Danish It has a big brother for the AA truck .Maybe Brad in Germany could identify them.
John in lovely sunny weather Suffolk County England . |
05-28-2021, 07:38 AM | #36 | |
Senior Member
Join Date: Feb 2015
Location: Australia
Posts: 1,971
|
Re: Vintage Precision Hub Puller
Quote:
The APCO gauge fits these housings which are said to be 1/2 inch. https://www.oneillvintageford.co.uk/...ter_Pipes.html From the VP web site "Typically, electric temperature gauges use 1/4" NPT senders and mechanical gauges use 1/2" NPT senders. The Vintage Precision Thermostat Housing has (1) 1/2" NPT port and (1) 1/4" NPT port. Because mechanical gauges that use the 1/2” NPT port have temp senders that occasionally run long, they can stick too far into the housing and interfere with the function of the thermostat. Available upon request, we can include a 1/2” NPT bushing ($5.00) that will offset your temp sender safely away from the thermostat." |
|
05-28-2021, 09:38 AM | #37 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 581
|
Re: Vintage Precision Hub Puller
This is the one that I made like the one pictured on ebay. It works real well on Model A and also on the 40-48 Ford rear hubs.
|
05-28-2021, 09:42 AM | #38 |
Senior Member
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,849
|
Re: Vintage Precision Hub Puller
|
05-28-2021, 09:52 AM | #39 |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,046
|
Re: Vintage Precision Hub Puller
I'd suggest turning that axle nut over before applying pressure on it.
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
05-28-2021, 03:59 PM | #40 |
Senior Member
Join Date: May 2020
Location: Corning NY
Posts: 244
|
Re: Vintage Precision Hub Puller
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|