|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-05-2016, 11:38 AM | #1 |
Senior Member
Join Date: Jul 2014
Location: Boxborough, MA
Posts: 274
|
Ammonia instead of carb cleaner?
Since its too cold to work in the barn today, I've decided to begin rebuilding one of the carburetors I have on the shelf. Now that tear-down is complete, I have to ask: is using ammonia just as effective as the much more expensive carb cleaner to soak it? Les Andrews touches briefly on this in his Zenith overhaul section in Vol. 1. Is this worth doing?
Thanks! |
03-05-2016, 01:04 PM | #2 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Ammonia instead of carb cleaner?
I've cleaned them in a pot, on the stove, with TIDE & WATER.
Bill Clean
__________________
"THE ASSISTANT GURU OF STUFF" |
Sponsored Links (Register now to hide all advertisements) |
|
03-05-2016, 01:24 PM | #3 |
Senior Member
Join Date: Sep 2012
Location: Eureka, California
Posts: 1,716
|
Re: Ammonia instead of carb cleaner?
NO ! Ammonia is not nearly as effective at cleaning anything (well, just about anything) as is Carburetor cleaner.
I found this out while cleaning out the fonts and 'burners' of my 15 or so Kerosene Lamps. While some recommend ammonia for cleaning lamps (and I did a bunch of lamps this way) ammonia did not work nearly as well (effective, thorough, timely) as did carb. cleaner. I would presume that the same results would be for cleaning a carburetor. |
03-05-2016, 02:02 PM | #4 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Ammonia instead of carb cleaner?
I use my sandblast cab on the zenith's... I then wash it off and flush all the ports out with carb cleaner and a straw
|
03-05-2016, 02:08 PM | #5 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Ammonia instead of carb cleaner?
I do the same as Mitch.
If I find a passage totally blocked, then I remove the brass plug to clean it out, otherwise I leave the brass plugs alone. |
03-05-2016, 02:42 PM | #6 |
Senior Member
Join Date: Jul 2014
Location: Boxborough, MA
Posts: 274
|
Re: Ammonia instead of carb cleaner?
Sponsored Links (Register now to hide all advertisements)
|
03-05-2016, 02:48 PM | #7 | |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Ammonia instead of carb cleaner?
Quote:
Dad W.
__________________
"THE ASSISTANT GURU OF STUFF" |
|
03-05-2016, 02:51 PM | #8 |
Senior Member
Join Date: Jul 2010
Location: Pennsylvania
Posts: 1,106
|
Re: Ammonia instead of carb cleaner?
Ammonia will dissolve the brass plugs in the passage ways if you soak the carb too long.
|
03-05-2016, 02:57 PM | #9 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Ammonia instead of carb cleaner?
I don't wear glasses
Last edited by Mitch//pa; 03-05-2016 at 03:34 PM. |
03-05-2016, 03:29 PM | #10 |
Senior Member
Join Date: May 2010
Posts: 4,179
|
Re: Ammonia instead of carb cleaner?
FWIW:
"If" one wants to experiment with a few things that "really" works, and will not harm metal for cleaning cast iron carburetors or pot metal carburetors : 1. Cast Iron or Pot Metal: POR 15 "Marine Clean" is a water based chemical specially formulated material that attacks petroleum products like paint remover attacking dry, cured paint .......... it emulsifies petroleum products as opposed to thinning petroleum products. It reaches deep down in the pores of metal where afterwards, the emulsified petroleum residue can be rinsed off with water. After said use, (sometimes with more than one application), the metal is "oil free & petroleum product free" ....... hence, it will rust quickly in humid areas if not treated or painted to seal metal pores. 2. Non-Ferrous Carburetor Screws and Jets: Used successfully only by vintage mechanics that I knew since the Model T days: A. For non-believers, please find the most tarnished pennies one can find and allow several of them to soak in two (2) separate solutions. a. Solution A: Your most favorite and strongest Carburetor Jet and Carburetor Screw Cleaner. b. Solution B: Louisiana Hot Sauce. After 10 minutes soaking, please, please, look at the pennies in each solution. Hmmmmmmmmmmmmmm ..... Besides steel wires, wire brushes, lacquer thinner, carburetor cleaner, etc., etc., ................... What was in "most" mechanics' shops for cleaning insides and outsides of Carburetor Jets for the past 90 years? Last edited by H. L. Chauvin; 03-05-2016 at 03:31 PM. Reason: typo |
03-05-2016, 04:22 PM | #11 |
Senior Member
Join Date: Jul 2014
Location: Boxborough, MA
Posts: 274
|
Re: Ammonia instead of carb cleaner?
So a gallon of Franks would do it? Or should one try Tobasco?
|
03-05-2016, 05:18 PM | #12 |
Senior Member
Join Date: May 2010
Posts: 4,179
|
Re: Ammonia instead of carb cleaner?
FWIW:
"Louisiana Hot Sauce" was prescribed on the above very potent "Prescription" because of the Cayenne content .............. LOL Stick with the "Prescription" made with only with Cayenne Peppers, e.g.: ---------------------------------------------------------------------------------- Cayenne pepper is a certain remedy for heart attack; as a stimulant, it can start the heart into action again, and as it facilitates blood flow throughout the body, it will keep the heart going. Used as a heart attack preventative, along with the mucusless diet and a healthful life-style, Cayenne can do wonders in toning and rebuilding the heart and keeping it in top condition. ------------------------------------------------------------------------------------------------ Maybe keep a bottle in your Model A if you have occasional chest pains. Why change the "Prescription" when one know what works for carburetor jets. The "Louisiana", and "Crystal" brands are still using vintage Cayenne Peppers as opposed to chili peppers and jalapeno peppers and God knows what. Hope this helps ...... similar to MMO ..... LOL |
03-05-2016, 11:44 PM | #13 |
Senior Member
Join Date: Apr 2014
Posts: 709
|
Re: Ammonia instead of carb cleaner?
|
03-06-2016, 02:04 PM | #14 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,377
|
Re: Ammonia instead of carb cleaner?
Yes, safety glasses! If you don't think eye protection is important, ask the man who has one.
|
03-07-2016, 11:42 AM | #15 |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,057
|
Re: Ammonia instead of carb cleaner?
Only one set of eyes to a customer.
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
03-07-2016, 01:36 PM | #16 | |
Senior Member
Join Date: Sep 2013
Posts: 3,005
|
Re: Ammonia instead of carb cleaner?
Quote:
|
|
03-07-2016, 01:50 PM | #17 | |
Senior Member
Join Date: May 2010
Location: Central, IL
Posts: 3,968
|
Re: Ammonia instead of carb cleaner?
Quote:
Ive seen the mediablast method work the best.
__________________
1929 Model AA - Need long splash aprons! |
|
06-10-2023, 03:45 PM | #18 | |
Member
Join Date: Jul 2022
Location: Brookfield Ct.
Posts: 61
|
Re: Ammonia instead of carb cleaner?
Quote:
|
|
06-10-2023, 07:03 PM | #19 |
Senior Member
Join Date: Dec 2013
Location: Waxahachie, Texas
Posts: 956
|
Re: Ammonia instead of carb cleaner?
Forget all the other gee whiz cleaners out there. Go down to your Ford dealers' parts department and buy a can of this. This stuff really works. You will be amazed at how well it cleans.
|
06-10-2023, 07:03 PM | #20 |
Senior Member
Join Date: Dec 2013
Location: Waxahachie, Texas
Posts: 956
|
Re: Ammonia instead of carb cleaner?
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|