|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-21-2017, 05:39 PM | #1 |
Senior Member
Join Date: Aug 2013
Location: Stafford, VA
Posts: 115
|
Temp gauge installation
I plan to install a lower water inlet with a port to install a water temp gauge. . . seems pretty easy. Looking for any advice/guidance.
|
09-21-2017, 05:43 PM | #2 |
Senior Member
Join Date: Feb 2015
Location: Lone Jack Missouri
Posts: 381
|
Re: Temp gauge installation
|
Sponsored Links (Register now to hide all advertisements) |
|
09-21-2017, 05:44 PM | #3 |
Senior Member
Join Date: Aug 2013
Location: Stafford, VA
Posts: 115
|
Re: Temp gauge installation
I am. I didn't predict that. Is it off by much
|
09-21-2017, 05:48 PM | #4 |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Temp gauge installation
The reading you get from there will be waaay low because it will be reading the temperature AFTER your coolant has gone through the the radiator. How much depends on how well your radiator does its job. The best place for the sensor is in the water outlet at the front of the head.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. Last edited by Synchro909; 09-21-2017 at 06:01 PM. |
09-21-2017, 05:53 PM | #5 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Temp gauge installation
Probably about 20 degrees low reading.
|
09-21-2017, 07:00 PM | #6 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Temp gauge installation
Sponsored Links (Register now to hide all advertisements)
If he put one in the TOP & one in the BOTTOM, he could KNOW if the radiator was doing a good job or not.---LOL Bill Idiot
__________________
"THE ASSISTANT GURU OF STUFF" |
09-21-2017, 10:19 PM | #7 |
Senior Member
Join Date: Feb 2013
Location: Monterey Peninsula,California
Posts: 194
|
Re: Temp gauge installation
Several Parts Houses Sell A Short tube with a fitting for a temp. sending unit that fits in the top radiator hose. I have used them in the past worked great
|
09-22-2017, 08:06 AM | #8 |
Senior Member
Join Date: Oct 2014
Location: Kentucky
Posts: 502
|
Re: Temp gauge installation
Go with Vintage Precision great product and has outlet for gauge. Easy to take apart and clean out. ( rust flakes will collect on the inbound side of the thermos.)
|
09-22-2017, 09:40 AM | #9 |
Senior Member
Join Date: Dec 2014
Location: Shawnee, Ok
Posts: 3,471
|
Re: Temp gauge installation
Housing, gauge and thermostat, dash
__________________
Keith Shawnee OK '31 SW 160-B |
09-22-2017, 06:45 PM | #10 |
Senior Member
Join Date: Aug 2013
Location: Stafford, VA
Posts: 115
|
Re: Temp gauge installation
Thank you Sir
|
09-22-2017, 06:47 PM | #11 |
Senior Member
Join Date: Aug 2013
Location: Stafford, VA
Posts: 115
|
Re: Temp gauge installation
Thank you Keith
|
09-22-2017, 11:55 PM | #12 |
Senior Member
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
|
Re: Temp gauge installation
Bill's idea is slicker than snot, ideal for the Model A. You could keep tabs on engine temp. and radiator efficiency. Then comes a sensor in the rear of the block to monitor rust corruption at 3&4, before the pistons began to grab the walls.
|
09-23-2017, 03:53 AM | #13 | |
Senior Member
Join Date: Oct 2014
Location: Keystone Heights, FL
Posts: 647
|
Re: Temp gauge installation
Quote:
__________________
I Love Anything That Turns Money Into Noise |
|
09-23-2017, 06:57 AM | #14 |
Member
Join Date: Jan 2011
Location: Central Maryland
Posts: 96
|
Re: Temp gauge installation
I replaced the gooseneck above the water pump with one that has a boss for a temperature sensor and it works very well. Routed the line through the junction box to the gauge mounted just below the speedometer. Very pleased with the installation.
|
09-23-2017, 09:12 AM | #15 | |
Senior Member
Join Date: Dec 2014
Location: Shawnee, Ok
Posts: 3,471
|
Re: Temp gauge installation
Quote:
__________________
Keith Shawnee OK '31 SW 160-B |
|
09-23-2017, 12:08 PM | #16 |
Senior Member
Join Date: Mar 2015
Location: Freetown, Massachusetts
Posts: 511
|
Re: Temp gauge installation
I did the top water outlet housing with the tapping for the temperature probe. It works impressively well.
__________________
Brian French; 1930 Briggs Town Sedan |
09-23-2017, 12:20 PM | #17 |
Senior Member
Join Date: Aug 2016
Location: Alberta
Posts: 930
|
Re: Temp gauge installation
|
09-23-2017, 01:18 PM | #18 |
Senior Member
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
|
Re: Temp gauge installation
Kill, aftermarket breather tube assy'. No right or wrong way.
|
09-23-2017, 01:36 PM | #19 |
Senior Member
Join Date: Aug 2016
Location: Alberta
Posts: 930
|
Re: Temp gauge installation
I didn't realize that this was an aftermarket accessory type thing. I guess I should have as all of the vendors sell fill tube caps that are just that, a cap with no tube. So if you just have the cap, how does the crankcase vent?.
|
09-23-2017, 01:47 PM | #20 |
Senior Member
Join Date: Nov 2016
Location: SoCal
Posts: 877
|
Re: Temp gauge installation
Through the cap. The tabs inside the cap hold it up off of the top of the tube.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|