|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-09-2023, 10:58 AM | #1 |
Member
Join Date: Nov 2021
Location: Central Mass.
Posts: 96
|
Max. current draw across stock ‘36 ignition switch?
I’m building the wiring harness for my 36 coupe, which is 12 V negative ground. Stock flathead powered, power-master alternator and starter, and electric fan via a fan relay. Headlights TBD. Also an under-dash Arvin heater with 12v fan. I’m guessing with 12v power my current draw across the stock on/off column drop switch won’t be a problem, but figured I would ask those who have been down this path before. I know I can add relays and or an additional master on/off switch for devices powered by “ignition” (aka not constant 12v) power, but it’s simpler to just put them all through the stock switch if it’s robust enough. And simpler is always better.
Thanks! Pat |
12-09-2023, 12:23 PM | #2 |
Senior Member
Join Date: Aug 2012
Location: Abq, NM
Posts: 3,607
|
Re: Max. current draw across stock ‘36 ignition switch?
It might be better to ask on the Early V8 forum, but in general... original 6 volt parts (in good condition) have double the current carrying capacity of similar '12 volt' designed parts.
|
Sponsored Links (Register now to hide all advertisements) |
|
12-09-2023, 01:48 PM | #3 |
Senior Member
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,485
|
Re: Max. current draw across stock ‘36 ignition switch?
IF it were me (IMO) -
I would put all on relays as there will be a better draw (lower resistance) and high amp is kept out of the cabin, especially with circuits like EFI, HOT IGN, ELECTRIC FUEL PUMP(S), ELECTRIC FAN(S), HDLPS, SOUND, etc,
__________________
***** We should have a contest. The player has to start at the very last post of a thread & then try to guess what the OP's original question was about ... |
12-16-2023, 04:30 PM | #4 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: Max. current draw across stock ‘36 ignition switch?
The old pre 1948 V8 Fords were set up for the ignition switch to only power the ignition with the instruments added after 1938. Lights and horn were connected directly to the power buss. Lights had a circuit breaker. The horn just had a relay by the end of the 1930s.
The ignition on the pre-1948 V8 Fords had a ballast of around 0.8 Ohms. This helped control the current through the old Mallory coils that were designed to attach to the helmet and early crab distributors. The post war rabbit ear distributors still used the ballast even though they have a remote mounted coil next to the generator. The whole system would draw near 4 amps and those switches are rated for near that figure with just a little fudge factor. Last edited by rotorwrench; 12-17-2023 at 11:57 AM. |
12-16-2023, 11:43 PM | #5 |
Senior Member
Join Date: Oct 2011
Location: elmira,ny
Posts: 1,518
|
Re: Max. current draw across stock ‘36 ignition switch?
On our '41, we had stereo & amp, ign, heater blower, elect fuel pump, charging ports for phone , elect. radiator fan & fog lamps all running thru the stock switch for 24 yrs and never had any problems.
|
12-17-2023, 11:55 AM | #6 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: Max. current draw across stock ‘36 ignition switch?
Sponsored Links (Register now to hide all advertisements)
|
12-17-2023, 02:23 PM | #7 | |
Member
Join Date: Nov 2021
Location: Central Mass.
Posts: 96
|
Re: Max. current draw across stock ‘36 ignition switch?
Quote:
|
|
12-17-2023, 07:56 PM | #8 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: Max. current draw across stock ‘36 ignition switch?
Aircraft use a continuously operating relay to power their electrical buss. It is controlled by a Master Switch. It sounds like you have something similar, so this is a reasonable way to power the buss and then apply fuses or circuit breakers to protect all the loads in the system. I still do all my wiring in accordance with the FAA Advisory Circular AC43.13-1B chapter 11. There is more info in that AC about standard electrical system practices than a person can easily find on regular google searches.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|