The Ford Barn

skidmarks · 07-16-2016, 09:03 PM

On a 32 ford 5 window. The car started out life as a trunk model and then changed to a rumble seat. Now it's going back to a trunk model. Lucky all the trunk hardware was laying loose in the floor.

Question is. The braces were the rumble seat hinges mount. The holes are booged up and I am going to repair them. From the factory were there no holes in these braces for trunk model cars?

DavidG · 07-16-2016, 10:15 PM

The vertical strainers (braces) were identical for both rumble seat and trunk versions of the '32 standard coupe.

skidmarks · 07-16-2016, 10:27 PM

The ones in the car I have ,The holes are large and odd shaped. I will post a picture tomorrow. Theye don't appear to be something I would think was original

DavidG · 07-17-2016, 05:35 AM

They were originally neither large nor in any shape other than round.

skidmarks · 07-17-2016, 12:06 PM

Here is a before and after. Now does it get a correct size and location put back into it?

skidmarks · 07-17-2016, 12:11 PM

Sponsored Links (Register now to hide all advertisements)

Also this is where the latch for the rumble lid was. Do these two holes stay as is for a trunk model or should they be welded shut.
Obviously the outside hole for the rumble lid gets welded shut but does the inside hole stay or should it be filled also.
Lucky enough when this was done the previous owner (s) never filled the holes for the trunk handle.

Nice thing is that it's all rust free

DavidG · 07-17-2016, 01:51 PM

Those two holes remain (see photo) and those on the lid for the latch and handle all should be filled, including the slot for the latch tongue and the two holes that bookend the slot to attach the latch.

TonyM · 07-17-2016, 03:09 PM

Quote:

Originally Posted by skidmarks

On a 32 ford 5 window. The car started out life as a trunk model and then changed to a rumble seat. Now it's going back to a trunk model. Lucky all the trunk hardware was laying loose in the floor.

Thank you.

There is a special place in Ford Heaven for you.

Save the Trunk Coupes.

34pickup · 07-17-2016, 03:15 PM

My coupe was also converted to a rumble seat by a previous owner and I had to put it back to a trunk. You will need this white panel for the lid to latch on to when you put the hinges back on the top.

skidmarks · 07-17-2016, 03:39 PM

Quote:

Originally Posted by 34pickup

My coupe was also converted to a rumble seat by a previous owner and I had to put it back to a trunk. You will need this white panel for the lid to latch on to when you put the hinges back on the top.

Lucky enough it came with all the original hardware including that panel.

07-16-2016, 09:03 PM	#1
skidmarks Senior Member Join Date: Aug 2010 Location: newark, delaware Posts: 3,735	32 ford coupe rumble seat question On a 32 ford 5 window. The car started out life as a trunk model and then changed to a rumble seat. Now it's going back to a trunk model. Lucky all the trunk hardware was laying loose in the floor. Question is. The braces were the rumble seat hinges mount. The holes are booged up and I am going to repair them. From the factory were there no holes in these braces for trunk model cars?

07-16-2016, 10:27 PM	#3
skidmarks Senior Member Join Date: Aug 2010 Location: newark, delaware Posts: 3,735	Re: 32 ford coupe rumble seat question The ones in the car I have ,The holes are large and odd shaped. I will post a picture tomorrow. Theye don't appear to be something I would think was original

07-17-2016, 05:35 AM	#4
DavidG Senior Member Join Date: May 2010 Location: southeastern Michigan Posts: 10,102	Re: 32 ford coupe rumble seat question They were originally neither large nor in any shape other than round.

07-17-2016, 01:51 PM	#7
DavidG Senior Member Join Date: May 2010 Location: southeastern Michigan Posts: 10,102	Re: 32 ford coupe rumble seat question Those two holes remain (see photo) and those on the lid for the latch and handle all should be filled, including the slot for the latch tongue and the two holes that bookend the slot to attach the latch.