|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-20-2013, 02:59 PM | #1 |
Senior Member
Join Date: Dec 2012
Location: Enterprise, WV.
Posts: 460
|
high compression heads
Never saw one of the high compression heads on the market. So why can't you shave the stock head to raise the compression. If so whats the max you can take off.
|
02-20-2013, 03:02 PM | #2 |
Senior Member
Join Date: May 2010
Location: Middletown Pa
Posts: 391
|
Re: high compression heads
This was covered a while back so it should show up in a search. Bottom line is the head is too thin to mill enough to raise compression.
|
Sponsored Links (Register now to hide all advertisements) |
|
02-20-2013, 04:04 PM | #3 |
Senior Member
Join Date: May 2010
Location: Windy City
Posts: 2,919
|
Re: high compression heads
The effect of milling the head is minor, just a few tenths increase. HC heads have a different, significantly smaller volume chamber geometry. Here's one that I am currently using, about 117.5cc. Stock is well over 200cc. Compare the shape to a stock head.
|
02-20-2013, 07:18 PM | #4 |
Senior Member
Join Date: May 2010
Location: Clinton,WA/Whidbey Island
Posts: 4,105
|
Re: high compression heads
What was the process to polish as in your picture??
__________________
www.whidbeymodelaclub.com |
02-20-2013, 09:03 PM | #5 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: high compression heads
In 1954, I milled one .075" & OH! YES! It was """FASTER"""! Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
02-20-2013, 10:24 PM | #6 |
Senior Member
Join Date: Dec 2011
Location: Jupiter, FL
Posts: 536
|
Re: high compression heads
Sponsored Links (Register now to hide all advertisements)
|
02-21-2013, 08:29 AM | #7 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: high compression heads
Hey, I was thinking, Why doesn't someone make domed valves to suck up a few of those extra CCs? I was told that some guys were welding up their combustion chambers. That sounds a little risky to me without a furnace. I have "Dropped" my spark plugs down about .030 for what ever gain that will give me. Jes thinkin' bout it!
Terry |
02-21-2013, 10:57 AM | #8 |
Senior Member
Join Date: May 2010
Posts: 4,179
|
Re: high compression heads
FWIW: Knew a machinist who lightened thousands of Model A flywheels & shaved thousands of Model A heads in the 1930's & 1940's.
He told me in the late 1950's that in the 1930's & 1940's that he could remove 3/16" from a standard Model A head with no problems to increase compression. Have no reason to doubt it, he was a well known respected machinist who provided intricate detailed work. |
02-21-2013, 11:19 AM | #9 | ||
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,519
|
Re: high compression heads
Quote:
Quote:
Yes, I don't doubt there were some that probably shaved .180-.200 off of a head trying to increase compression. I entered this in my computer engine simulator and came up with 4.735 c/r using 200cc as a baseline for head chamber volume. Naturally this calculation could be off but I dropped the volume of the chamber to 175 cc to compensate for the 3/16 cut and it raised the CR to 5.106703. Naturally someone would need to calculate the CC in real world to get an accurate chamber volume but a ¼ notch more of compression back then was about the most that one could expect. By today's standards, that doesn't seem worth the bother does it? |
||
02-21-2013, 11:41 AM | #10 |
Senior Member
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,089
|
Re: high compression heads
The shape of the chamber means a lot too. The A chamber would tend to detonate with high compression. The Winfield and Chrysler chambers are much better, similar to the Ford V8. Spark plug location is important too.
|
02-21-2013, 12:02 PM | #11 |
Senior Member
Join Date: May 2010
Posts: 4,179
|
Re: high compression heads
Brent,
Thanks, & if one wants to investigate further, one should be able to come fairly close to finding the cc differences on such shaved heads by: 1. Levelng an upside down un-shaved head, with spark plugs installed on a table using a level & fill one (1) standard combustion chamber with a liquid & measure the cc's added in a measuring cup. 2. Fill adjacent combustion chamber with same liquid to within 3/16" from top & measure difference in cc's. In knowing this particular machinist very well, he did all this work for free after work hours. Also have a hunch that all who requsted this flywheel & head machinist work in the 1930's & 1940's were under the age of 25, & were Depression Era youngsters trying to find an inexpensive way to impress others by increasing Model A acceleration & top speed -- even sounds familiar today. Last edited by H. L. Chauvin; 02-21-2013 at 12:04 PM. Reason: typo |
02-23-2013, 10:43 AM | #12 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: high compression heads
Not to beat a dead horse, but how does one hold a head down on the table of the milling machine? I tried it on a Bridgeport and it didn't work too well. If one skim cuts the bolt spotfaces so they're all in the same plane and then using some kind of 1-2-3 blocks under the skimmed off corner bolt surfaces and then use a T bolt thru the sparkplug hole, it would work, I think. I was using someone else's Bridgeport and couldn't tie the machine up for long. and the leveling wasn't level, so I gave up in mid job. Same thing on a grinding table except you have magnetism pulling for you.
Terry |
02-23-2013, 10:58 AM | #13 | |
Senior Member
Join Date: May 2010
Location: 60046
Posts: 888
|
Re: high compression heads
Quote:
tk
__________________
anyone need some Model A restoration work done in Illinois? shoot me an email for pics and information [email protected] |
|
02-23-2013, 01:57 PM | #14 |
Senior Member
Join Date: May 2010
Location: Eastern CT
Posts: 2,732
|
Re: high compression heads
|
02-23-2013, 02:43 PM | #15 | |
Senior Member
Join Date: May 2010
Location: Wa.
Posts: 5,409
|
Re: high compression heads
Quote:
The one I personally like best is the Storm Vulcan Headmaster which holds the head face up and it sits on jack stands, pulled down to the table by bolts either through the plug holes or tapped head stud holes. With the face up setup you can easily see what is going on and if any spots didn't clean up. No mirrors required as on some machines. It is extremely fast to set up with 2 bridge fixtures that the jacks push the head up against. Last edited by Pete; 02-23-2013 at 05:36 PM. |
|
02-23-2013, 05:45 PM | #16 | |
Senior Member
Join Date: May 2010
Location: Wa.
Posts: 5,409
|
Re: high compression heads
Quote:
Here is a pic of a V8 aluminum head and when you fill a model A head and remachine it to this chamber shape, it REALLY works. A stock cast iron A head could be reworked the same except the cost of welding would scare most people away. With the aluminum you can just wire weld it.(MIG) |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|