|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-04-2023, 10:26 PM | #1 |
Member
Join Date: Aug 2013
Location: Santa Clarita, CA
Posts: 63
|
Radiator, no overflow tube
I've been working on my vehicle over the last few months. Fixing things here and there. The engine runs a little better after each repair. And with each repair, I drive the car a little more. And with each drive, the engine will overheat sooner then the last drive.
I tore apart the cooling system. And I found that the gooseneck is in pretty bad shape. After draining the system, I found a lot of junk sitting atop the tubes in the radiator. (2 tube core) I replaced the gooseneck. I back flushed the engine. Back flushed the radiator. I let the radiator sit in vinegar for a few days, and continued to backflush it once a day. Now the tubes look really clean. And when I get the system put back together, I'll run it with vinegar for a week or so. Continuing to flush as I go. I'll check timing. Re calibration the carb mixture. Verify the correct coolant level, etc. So, the radiator makes a hellova mess every time it overheats. Boiling over at the cap, and draining all over the front end. I thought I would take a look at the overflow tube when I took the engine apart only to find that there is no overflow tube. I have 3' of 1/4" brass tubing. And I feel like it would be really easy to drill a hole into the radiator top reservoir, and weld in the tubing to make my own overflow. Any advice on adding in this tube? And is it common to find no overflow on these older radiators? |
09-04-2023, 10:43 PM | #2 |
Senior Member
|
Re: Radiator, no overflow tube
The radiator might be a bad reproduction or a previous owner(s) might have adapted a radiator from another car. Someone here might be able to identify it if you post a picture.
You probably should replace the gasket in the radiator cap and run distilled water with rust inhibitor until you fix the radiator. What model and year is your car? David Serrano |
Sponsored Links (Register now to hide all advertisements) |
|
09-04-2023, 11:21 PM | #3 |
Member
Join Date: Aug 2013
Location: Santa Clarita, CA
Posts: 63
|
Re: Radiator, no overflow tube
'28 coupe
|
09-05-2023, 06:40 AM | #4 |
Senior Member
Join Date: Jan 2012
Location: Western North Carolina
Posts: 4,148
|
Re: Radiator, no overflow tube
I use a thick O ring for the radiator cap gasket. That stopped it leaking at the cap. But even a fix for the cap will not keep it from overflowing if you do not have the overflow tube. You can use plain soft solder to install the overflow tube. I think it works best if towards the back of the radiator but double check as my memory may not be accurate.
__________________
A is for apple, green as the sky. Step on the gas, for tomorrow I die. Forget the brakes, they really don't work. The clutch always sticks, and starts with a jerk. My car grows red hair, and flies through the air. Driving's a blast, a blast from the past. |
09-05-2023, 07:59 AM | #5 |
Senior Member
Join Date: May 2010
Location: Hebron, CT
Posts: 444
|
Re: Radiator, no overflow tube
With the overflow tube missing you might be pumping water out of the radiator as you drive causing the engine to overheat.
|
09-05-2023, 08:53 AM | #6 |
Senior Member
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,163
|
Re: Radiator, no overflow tube
Sponsored Links (Register now to hide all advertisements)
__________________
AL in NY |
09-05-2023, 08:55 AM | #7 |
Member
Join Date: Aug 2013
Location: Santa Clarita, CA
Posts: 63
|
Re: Radiator, no overflow tube
Exactly nkaminar. The backside of the radiator has an overhang where I was considering adding the tube. Running it down the drivers side. I'll also replace the gasket on the cap.
Last edited by izze; 09-05-2023 at 09:02 AM. |
09-05-2023, 10:10 AM | #8 |
Member
Join Date: Oct 2022
Location: Findlay, Ohio
Posts: 95
|
Re: Radiator, no overflow tube
I would add the overflow tube but go with copper instead of brass and soldering instead of welding. I also put a 2" roofing nail in the overflow tube of mine to help eliminate it splashing out while running at 45 m.p.h.
|
09-05-2023, 10:47 AM | #9 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,847
|
Re: Radiator, no overflow tube
I agree with David, with two rows it's most likely a cheap reproduction radiator.
|
09-05-2023, 11:27 AM | #10 |
Member
Join Date: Aug 2013
Location: Santa Clarita, CA
Posts: 63
|
Re: Radiator, no overflow tube
@Ramman. Why would you use copper over brass?
|
09-05-2023, 04:48 PM | #11 |
Member
Join Date: Oct 2022
Location: Findlay, Ohio
Posts: 95
|
Re: Radiator, no overflow tube
For me it's ease of forming kink free bends and soldering skills.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|