|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-23-2024, 04:57 PM | #1 |
Member
Join Date: Nov 2022
Location: Southern Massachusetts
Posts: 37
|
47 front floorpan
Does anyone have a photo of the removable front floorpan in their car?
Also, what is the proper size of the fasteners that secure it? Cody
__________________
No job is so important and no service is so urgent- that we cannot take time to perform our work safely. -Bell System |
02-23-2024, 05:30 PM | #2 |
Senior Member
Join Date: Jan 2011
Location: Albion, PA
Posts: 713
|
Re: 47 front floorpan
Third Gen in TN. has a kit for the fasteners.
|
Sponsored Links (Register now to hide all advertisements) |
|
02-23-2024, 05:45 PM | #3 |
Senior Member
Join Date: Jan 2011
Location: Albion, PA
Posts: 713
|
Re: 47 front floorpan
42 floorboard.jpg
Here is a picture of the floorboard from my 42. Should be the same 42-48 with most 48's being made out of aluminum instead of steel. |
02-23-2024, 05:50 PM | #4 |
Senior Member
Join Date: Jan 2011
Location: Albion, PA
Posts: 713
|
Re: 47 front floorpan
46 floorboard.jpg
Here is a shot of my 46 with the floorboard in position. |
02-23-2024, 06:04 PM | #5 | |
Senior Member
Join Date: May 2015
Posts: 8,151
|
Re: 47 front floorpan
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
02-23-2024, 06:04 PM | #6 | |
Senior Member
Join Date: May 2015
Posts: 8,151
|
Re: 47 front floorpan
Sponsored Links (Register now to hide all advertisements)
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
02-23-2024, 07:40 PM | #7 |
Member
Join Date: Nov 2022
Location: Southern Massachusetts
Posts: 37
|
Re: 47 front floorpan
Appreciate it, thank you for the photos. I'm going to order the hardware kit.
While I was looking for the hardware, I noticed a 1941-48 Ford floor toe board plugs/bumpers set listed. When removing my floorboard, I noticed one of these lying under the car. Any idea where they would go under the floorboard?
__________________
No job is so important and no service is so urgent- that we cannot take time to perform our work safely. -Bell System |
02-23-2024, 09:39 PM | #8 |
Senior Member
Join Date: Jan 2011
Location: Albion, PA
Posts: 713
|
Re: 47 front floorpan
I think they go in the four holes on the floor portion about an inch or so before the curve starts to the firewall. Get the seal kit also. I had to trim it to fit on my 42.
Last edited by 1942deluxe; 02-27-2024 at 09:29 PM. |
02-27-2024, 05:56 PM | #9 |
Senior Member
Join Date: May 2010
Location: Lower Hutt , New Zealand
Posts: 2,126
|
Re: 47 front floorpan
Yep the bumpers fit into pre pressed holes. I second getting a seal kit too. Just a note.. you might find the holes in the floor have "flogged out" over the the year and may have to fit bigger screws or get some large speed clips for the floor side of the set up.
GB
__________________
"you can't make honey out of dog sh*t" "You're a long time looking at the lid" |
02-27-2024, 09:52 PM | #10 | |
Member
Join Date: Nov 2022
Location: Southern Massachusetts
Posts: 37
|
Re: 47 front floorpan
Quote:
__________________
No job is so important and no service is so urgent- that we cannot take time to perform our work safely. -Bell System |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|