|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
|
05-13-2013, 07:11 PM | #1 |
Senior Member
Join Date: May 2010
Location: ca.
Posts: 2,522
|
piston/block heigth
how much piston can go above the block ? ie: .015 ... .020 etc .
pistons are hitting head , but not sure if head has been cut .... thanks .. steve
__________________
V4f |
05-13-2013, 07:25 PM | #2 |
Senior Member
Join Date: May 2010
Location: Asheville,NC
Posts: 3,104
|
Re: piston/block heigth
I have run pistons that were .030 above the deck and a head that was FLAT and have never had a piston hit. The gasket is .060 and will compress .015 leaving plenty.
__________________
http://www.model-a-ford-4bangers.com/ |
Sponsored Links (Register now to hide all advertisements) |
|
05-13-2013, 07:58 PM | #3 |
Senior Member
Join Date: May 2010
Location: Windy City
Posts: 2,919
|
Re: piston/block heigth
Just for the record an original stock block with 11.500" deck height had the pistons 0.0315" above deck if all else was to spec. The blocks themselves were spec'ed at 11.500 -11.505" and usually came off the machining line nearer the high limit.
At 3,000 rpm you won't get much rod stretch, perhaps 0.005", but there are other factors. Both the aluminum piston from pin center to face, and the rod will run hotter than the block temperature and will therefore exhibit greater expansion increasing the piston protrusion. In an A this could add up to an additional 0.015". Ideal 'squish' height is debateable, but should it get less than 0.020" it is possible to initiate detonation despite a relatively low compression ratio. |
05-14-2013, 01:22 AM | #4 |
Senior Member
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,787
|
Re: piston/block heigth
MikeK, Are you sure that less than .020" squish height will cause detonation? My experience has been the opposite; it will lessen detonation. Here's why: After the spark plug fires, a flame front advances across the combustion chamber, building pressure (and thus heat) ahead of it. Under high load/heat situations, this pressure ahead of the flame can auto-ignite the fuel/air mixture in the far reaches of the chamber (the squish area above the piston). So now you have two flame fronts heading towrd each other. When they collide, BAM! detonation! With a tight squish height there is less room for a second flame front to form. Also, with a small squish height, there is greater turbulence as the piston reaches TDC, which better mixes the air and fuel, making for a faster burn (less time for detonation to occur and less spark advance needed).
|
05-14-2013, 11:01 AM | #5 | |
Senior Member
Join Date: May 2010
Location: Windy City
Posts: 2,919
|
Re: piston/block heigth
Quote:
If you're really into it, properly placed Singh grooves on the head squish area will help. |
|
05-14-2013, 08:48 AM | #6 |
Senior Member
Join Date: May 2010
Location: ca.
Posts: 2,522
|
Re: piston/block heigth
Sponsored Links (Register now to hide all advertisements)
__________________
V4f |
05-14-2013, 11:54 AM | #7 |
Senior Member
Join Date: May 2010
Location: ca.
Posts: 2,522
|
Re: piston/block heigth
ok , i took measurements this morning ... stock head (*maybe shaved)
head : the chambers (not the valve area , just the flat where the piston is) .. .085 piston above the block : 1) .065 2) .085 **************** 3) .040 4) .068 used head gasket : .070-.075 thick ****** any info greatly appreciated .............. thanks .. steve
__________________
V4f |
05-14-2013, 01:18 PM | #8 |
Senior Member
Join Date: May 2010
Location: Windy City
Posts: 2,919
|
Re: piston/block heigth
The huge variance indicates one of two things. Either the rod lengths are uneven or the crank was reground without indexing and no attempt was made to set the stroke to spec.
Crank each piston down to BDC and measure the depth from the deck. Add the above-deck measurements. They should all equal factory stroke: 4.250" If not, the crank is way off. If they do equal 4.250", the rod lengths are off. You may have a combo of the two. Other contributing factors: The deck may not be machined parallel to the pan rail (datum reference zero), and/or the crank main bearing centers may have been bored above/below zero. These last two would add or subtract progressively from front to back. |
05-14-2013, 03:26 PM | #9 |
Senior Member
Join Date: Apr 2011
Location: New Zealand
Posts: 444
|
Re: piston/block heigth
My rebuilt motor with 100thou oversize pistons had the pistons 50thou above the block. The new Winfield 7:1 aluminum head had a flush face and so I had to get it machined to clear the pistons. the combustion chambers were prettty rough too and I got those polished.
I had always understood that the original pistons stood proud of the block but had no idea by how much. Keith |
05-14-2013, 03:36 PM | #10 |
Senior Member
Join Date: May 2010
Location: ca.
Posts: 2,522
|
Re: piston/block heigth
apparently who ever had this redone yes ago , cut to many corners . block is cut , head is cut . quit a mess but figured out how to fix it . thanks all for your help .
THE FIX : new head , solid copper spacer & copper head gasket to clear the pistons ! so glad its not mine !! ............. steve
__________________
V4f |
05-14-2013, 05:58 PM | #11 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,393
|
Re: piston/block heigth
Are you making the copper spacer or are they available by someone??
Paul in CT |
05-14-2013, 06:09 PM | #12 |
Senior Member
Join Date: May 2010
Location: ca.
Posts: 2,522
|
Re: piston/block heigth
ive been told that they are made of solid cooper @ .062 by a vendor......... still looking ... steve
__________________
V4f |
05-14-2013, 07:39 PM | #13 |
Senior Member
Join Date: Feb 2011
Location: Cocoa, Florida
Posts: 1,609
|
Re: piston/block heigth
So did you measure as Mike suggested? What did you find or what is the bottom line issue as to why the piston heights are varied?
__________________
Wanted: Simmons Super Power Head Craig Likon 1931 150B |
05-14-2013, 09:13 PM | #14 |
Senior Member
Join Date: May 2010
Location: Santa Rosa, CA
Posts: 1,282
|
Re: piston/block heigth
Take the necessary metal off the top of the piston. No need for a new head or custom gasket. How much to take off depends on the pop up and how much squish you want. I like .045-.055. Pistons are fine so long as there is .200 material remaining on the piston top, maybe even less depending on the Compression Ratio. Works for me with a Weiand 7-1 flat top head and a Best .060 thick gasket that compresses down to about .055.
|
05-14-2013, 10:10 PM | #15 |
Senior Member
Join Date: May 2010
Location: ca.
Posts: 2,522
|
Re: piston/block heigth
i have not been back to the car today . so no measurement .
i hate cutting pistons with out rebalancing . gonna try the porrmans fix as above .... thanks .. steve
__________________
V4f |
05-14-2013, 11:13 PM | #16 |
Senior Member
Join Date: May 2010
Location: Santa Rosa, CA
Posts: 1,282
|
Re: piston/block heigth
Steve: If you are still looking, Charlie Yapp at Secrets of Speed advertises the .062 solid copper gaskets.
|
05-15-2013, 09:13 AM | #17 |
Senior Member
Join Date: May 2010
Location: ca.
Posts: 2,522
|
Re: piston/block heigth
pc/sr ... thank you !!! ................
__________________
V4f |
05-15-2013, 02:04 PM | #18 |
Senior Member
Join Date: May 2010
Location: ca.
Posts: 2,522
|
Re: piston/block heigth
well charlie no longer makes them . any ideas ? a good used one ! thanks .. steve
__________________
V4f |
05-15-2013, 04:00 PM | #19 |
Senior Member
Join Date: May 2010
Posts: 397
|
Re: piston/block heigth
Solid copper gaskets are notorious for seeping. I think you will have more problems especially around the studs. I'm getting ready to use one as I cannot buy a head gasket to fit the head I'm going to use. I had mine annealed by a firm in Valencia Ca. I purchased it from Taylor Engine several years ago.
Last edited by just plain bill; 05-16-2013 at 12:41 PM. |
05-15-2013, 02:20 PM | #20 |
Senior Member
Join Date: May 2010
Location: Windy City
Posts: 2,919
|
Re: piston/block heigth
any ideas?... Yes. Fix the problem rather than trying to band-aid the symptom. With pistons up and down like you describe in post #7 that thing is going to run like a cement mixer. A thicker gasket is not the answer.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|