|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-09-2016, 02:08 PM | #1 |
Member
Join Date: Oct 2010
Location: Oklahoma City, Ok.
Posts: 31
|
Need a part ID, name and hopefully a source please
Part is for a '41 woodie but I think any '41 model and possibly up to '48 will work. On the drivers side along the seam between the top of the front inner fender and the fender itself are a series of carriage bolts that fasten the two pieces together. On some or all of these bolts is a piece of flat sheet metal bent in a U shape that are used to secure the hood pull cable to the fender and keep it from flopping around.
Can anyone help with the correct nomenclature, Ford part number or even better a source for these cable clips. Thnx |
11-09-2016, 02:29 PM | #2 |
Senior Member
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
|
Re: Need a part ID, name and hopefully a source please
If this not a concours vehicle, most hardware stores have a selection of 'loop clamps' that would do the job.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES |
Sponsored Links (Register now to hide all advertisements) |
|
11-09-2016, 02:37 PM | #3 |
Senior Member
Join Date: May 2010
Posts: 218
|
Re: Need a part ID, name and hopefully a source please
Try calling Roy Nacewicz , they may have the correct part.
|
11-09-2016, 09:41 PM | #4 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,757
|
Re: Need a part ID, name and hopefully a source please
I think what you are looking for is 11A-16899-A for center takes 2 or 3 and
11A-16899-B for front takes 1. Bob |
11-09-2016, 10:27 PM | #5 |
Member
Join Date: Oct 2010
Location: Oklahoma City, Ok.
Posts: 31
|
Re: Need a part ID, name and hopefully a source please
Bob thanks for the parts number, I'm searching the net hoping for a photo of the part to confirm the info
|
11-09-2016, 10:53 PM | #6 | |
Senior Member
Join Date: Nov 2015
Location: North Pole, Alaska
Posts: 2,651
|
Re: Need a part ID, name and hopefully a source please
Sponsored Links (Register now to hide all advertisements)
Quote:
May not be factory, but I have used them extensively on old cars. |
|
11-10-2016, 09:38 AM | #7 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,440
|
Re: Need a part ID, name and hopefully a source please
Some of the old Ford parts manuals contain illustrations of different clips used in manufacture of the early V8s. Part number specific ones may be different though. Adel clamps come in all sorts of sizes and composition. Some are cushioned and some are not. AC Spruce carries some. http://www.aircraftspruce.com/search...+clamp&x=0&y=0
Roy may be a good starting place looking for an original type. |
11-10-2016, 10:30 AM | #8 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,951
|
Re: Need a part ID, name and hopefully a source please
Would it be possible to cut some strips of
thin sheet metal and form your own clips? |
11-10-2016, 10:58 AM | #9 |
Member
Join Date: Oct 2010
Location: Oklahoma City, Ok.
Posts: 31
|
Re: Need a part ID, name and hopefully a source please
I have a large stock of Adel clamps I was just looking for a bit better look. I've been experimenting with making my own and that would be second choice if I can't find originals.
|
11-10-2016, 12:03 PM | #10 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,757
|
Re: Need a part ID, name and hopefully a source please
If you have the green Ford parts book see page 367 and 368 for pictures.
Bob |
11-10-2016, 04:23 PM | #11 |
Senior Member
Join Date: Sep 2010
Location: Independence, VA
Posts: 423
|
Re: Need a part ID, name and hopefully a source please
Try Carolina Houdaille 704-333-6669
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|