|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-19-2022, 09:44 PM | #21 | |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Engine bearing questions
Quote:
Damn it - there goes another secret!
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
|
12-20-2022, 01:07 PM | #22 |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,046
|
Re: Engine bearing questions
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
Sponsored Links (Register now to hide all advertisements) |
|
12-20-2022, 02:18 PM | #23 |
Member
Join Date: Feb 2022
Location: Mill Hall, PA
Posts: 46
|
Re: Engine bearing questions
Engines out and I have some some numbers with plastigage.. With no shims the rear main is .0015”. The middle main with the existing .007” shims on each side has a clearance of about .002”. the front main started with .007” shims on both sides, with two .0035” shims left clearance is about .001”.
Is the front modern crank seal SNYDER’s sells any good? Is the small hole in the middle of the rear main worth worrying about, I think they got a little too aggressive with their groove work. |
12-20-2022, 08:07 PM | #24 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,436
|
Re: Engine bearing questions
Most oil groove cuts start near the rear side but don't extend all the way. The front of the grooves continue to the thrust face where it can get a bit of out flow as the bearing leaks down.
The little hole in the cap bearing likely accesses the drain tube so I wouldn't worry about it too much. Most don't have a hole there but they do have feed holes at the top bearing up into the cam chest. I've not used the late rubber oil seal on the front so I won't comment on that. I just use the plain packing seals in the front the way Henry's guys did it but they are harder to use. Your engine may be a bit loosey-goosey but it wouldn't be the first model A to run that way. I knew of a fellow that packed leather shoe tonques in his rods every other week or so to keep one from knocking, |
12-21-2022, 10:29 AM | #25 |
Senior Member
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,897
|
Re: Engine bearing questions
0.001 in the front is fine. 0.0015 in the rear is fine. 0.002 in the middle is a very slight bit loose but OK. Hole is OK. Check thrust clearance. Replace oil drain tube with new. Assemble with assembly lube.
I cannot comment about the Snyder replacement seal but the one engine that I have had with a rubber seal leaked. The seal was worn out. So my conclusion is that rubber seals wear out eventually. How are the rods?
__________________
A is for apple, green as the sky. Step on the gas, for tomorrow I die. Forget the brakes, they really don't work. The clutch always sticks, and starts with a jerk. My car grows red hair, and flies through the air. Driving's a blast, a blast from the past. |
12-21-2022, 11:42 AM | #26 | |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,046
|
Re: Engine bearing questions
Sponsored Links (Register now to hide all advertisements)
Quote:
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
|
12-21-2022, 07:37 PM | #27 |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Engine bearing questions
By modern front crank seal, I assume you mean this one. https://www.snydersantiqueauto.com/p...8848&cat=41694
I have used those for years - never a failure and easy to install. Of my 4 Model As, 3 have that seal and one of those engines has done about 60,000 HARD miles (Towing a trailer weighing as much as the car at 50mph all day, every day for months at a time.) I have only one engine with the original type seal and I used that because the area of the pulley where the seal runs was slightly pitted. It seems to be performing quite admirably. Conclusion: Both work well.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
12-23-2022, 08:09 PM | #28 |
Senior Member
Join Date: May 2010
Location: PASADENA, CA
Posts: 1,885
|
Re: Engine bearing questions
|
12-24-2022, 10:13 AM | #29 |
Senior Member
Join Date: Aug 2017
Location: SoCal Desert
Posts: 826
|
Re: Engine bearing questions
SANDING 101:
When sanding something like a bearing cap, it's EASY to NOT sand it level. One needs to constantly rotate the part in their hand while sanding. Rotate the part around 22.5° every 5-10 strokes. To much pressure at the fingertips and/or your palm are to hard to regulate by constant sanding in the same direction causing uneven/unlevel surfaces. Regards Bill |
12-24-2022, 02:21 PM | #30 |
Senior Member
Join Date: Sep 2022
Location: SoCal
Posts: 591
|
Re: Engine bearing questions
You should use a jack to hold the crank against the upper bearing surface. It needs to be zero clearance at the top or that space will give a false reading on the plasti gauge.
|
12-28-2022, 05:41 PM | #31 |
Member
Join Date: Feb 2022
Location: Mill Hall, PA
Posts: 46
|
Re: Engine bearing questions
Thank you everyone for the great advice! Still waiting on parts.I’m so glad I listened and pulled the engine, I couldn’t be doing a good job from underneath with all I found wrong. All the bearing clearances are down to .001”–.0015”. Things that I found wrong that were contributing to the oil leak.:
1. A shim .007”on only one side of the rear main. 2. Excessive clearance on two of the main bearings. 3. The rear upper main bearing “seal “was sticking above the block several thousands creating a gap under the cap. 4. The oil return tube was only half as long as it should have been, and where it screws into the main has a small piece missing and probably was not sealed well. |
12-28-2022, 06:43 PM | #32 |
Senior Member
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,897
|
Re: Engine bearing questions
Yeah. It seems like extra work to pull the engine but in the long run it results in less work and a better job. Not to mention less oil and grease in your hair.
__________________
A is for apple, green as the sky. Step on the gas, for tomorrow I die. Forget the brakes, they really don't work. The clutch always sticks, and starts with a jerk. My car grows red hair, and flies through the air. Driving's a blast, a blast from the past. |
12-28-2022, 07:00 PM | #33 |
Senior Member
|
Re: Engine bearing questions
Working under your car gives your hair that oiled and combed back 1930's look.
But I would pull the engine it is more enjoyable. Dan |
01-05-2023, 01:19 AM | #34 |
Senior Member
Join Date: Nov 2011
Location: Sonoma, CA.
Posts: 1,497
|
Re: Engine bearing questions
Using this front oil seal, it uses a real seal instead of the solid rubber one.
|
01-05-2023, 01:27 PM | #35 |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: Engine bearing questions
|
01-07-2023, 01:24 AM | #36 |
Senior Member
Join Date: May 2010
Location: Santee Calif.
Posts: 509
|
Re: Engine bearing questions
|
01-07-2023, 05:27 PM | #37 |
Member
Join Date: Feb 2022
Location: Mill Hall, PA
Posts: 46
|
Re: Engine bearing questions
Went for a test drive, not expecting perfection, but so far no leaks. Also, the new Mitchell transmission is working really well. Along with a synchronized second and third gear it also has a higher ratio first and second gear. A V8 pressure plate is also working well.
Thanks everyone! |
01-08-2023, 12:39 AM | #38 |
Senior Member
|
Re: Engine bearing questions
Dodge
Who is the supplier of that seal, and do you have a part #? Thanks |
01-15-2023, 04:10 PM | #39 |
Junior Member
Join Date: Oct 2022
Posts: 4
|
Re: Engine bearing questions
Hey Congrats on getting the oil leaks fix! I am about to embark on this journey myself with my 29 coupe. If you wouldn't mind, could you share the link to the seals you ended up using? Hoping to get my pan off in the next few weeks and once i get eyes on things i'll be ready to order parts.
Thanks |
01-15-2023, 08:19 PM | #40 |
Member
Join Date: Feb 2022
Location: Mill Hall, PA
Posts: 46
|
Re: Engine bearing questions
I used the rope seal from Snyders for the front. I’m glad I did because the modern seal I do not believe would have worked because the crank was not centered in the hole, it was much closer to the timing cover than the pan.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|