|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-18-2019, 08:25 AM | #1 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Transmission Reassembly
How hard is it to put a transmission back together to the bellhousing with the throw out bearing and replace the clutch disk? Then put it back in the car and then the rear end all for someone eho has never done it before.
__________________
"The more things change, the more they stay the same." |
09-18-2019, 08:41 AM | #2 |
Senior Member
Join Date: Apr 2013
Location: Northwest CT
Posts: 1,092
|
Re: Transmission Reassembly
As someone who was in your shoes a couple months ago the short answer is not that hard.
I didn't touch the clutch since it's basically new but I did do everything else. I reinstalled mine by myself and heaved it in through the passenger door. Everything slid together without much fighting and then I realized I forgot the throwout bearing... the second time was much harder. Guess I only had enough steam for one run through. To get the rear end back in place I used a jack under the banjo and a jack under the radius rod to torque tube attachment point. A couple times adjusting the jacks and shuffling things around and everything went right together. |
Sponsored Links (Register now to hide all advertisements) |
|
09-19-2019, 10:30 AM | #3 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Transmission Reassembly
I am having trouble getting the throwout bearing off of the hub. It almost seems like it is one piece. Could you use a multidisk throwout on a single disk trans?
__________________
"The more things change, the more they stay the same." |
09-19-2019, 10:53 AM | #4 |
Member
Join Date: Nov 2016
Location: Corrupt-A -Cut Eastern,Ct
Posts: 54
|
Re: Transmission Reassembly
Use a ratchet strap around the trans hooked around the dash to cradle the assembly.
a couple of 3/8 -18 bolts with heads cut off screwed in engine side will acts like down pins. about 2.5 to 3" long on bolts. Bob |
09-19-2019, 11:09 AM | #5 |
BANNED
Join Date: Sep 2017
Posts: 385
|
Re: Transmission Reassembly
In answer to your question about the Bearing being the same: NO that whole system is/was different, including the gear box..
|
09-19-2019, 11:22 AM | #6 | |
Senior Member
Join Date: Apr 2013
Location: Northwest CT
Posts: 1,092
|
Re: Transmission Reassembly
Sponsored Links (Register now to hide all advertisements)
Quote:
Shouldn't be on the hub that tight. Support the bearing in a vice and a few taps on the hub with a drift should free it right up. |
|
09-19-2019, 11:39 AM | #7 |
BANNED
Join Date: Sep 2017
Posts: 385
|
Re: Transmission Reassembly
|
09-19-2019, 01:06 PM | #8 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Transmission Reassembly
Here are some pictures.
__________________
"The more things change, the more they stay the same." |
09-19-2019, 01:50 PM | #9 |
Senior Member
Join Date: Apr 2013
Location: Northwest CT
Posts: 1,092
|
Re: Transmission Reassembly
Looks like it's been there for a while but it should come off.
|
09-19-2019, 03:56 PM | #10 |
BANNED
Join Date: Sep 2017
Posts: 385
|
Re: Transmission Reassembly
|
09-19-2019, 06:16 PM | #11 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Transmission Reassembly
Got it off finally. It is an older one for sure. One step closer to getting it back in the car. Will keep you guys updated.
__________________
"The more things change, the more they stay the same." |
09-19-2019, 09:55 PM | #12 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Transmission Reassembly
Update: i tried to put the new bearing on the hub and it went on with absolutely no resistance, which I am going to take a wild guess here and say that means I need a new hub?
__________________
"The more things change, the more they stay the same." |
09-19-2019, 10:16 PM | #13 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Transmission Reassembly
The only point of contention might be the long bearing Vs the short bearing. Asides from that it's pretty straight forward. Not rocket science! There is a video on youtube and the guy shows you exactly how to do it. He has a clever mounting method. He drills a tight hole in a piece of 2X and works a (I think) a 3/4 nipple into the wood. Then using the open drain plug ,then he screws the trans case down it. It's stable and a nice assy. rig and very simple to make. Good luck with it!
Terry |
09-19-2019, 10:27 PM | #14 | |
BANNED
Join Date: Sep 2017
Posts: 385
|
Re: Transmission Reassembly
Quote:
|
|
09-20-2019, 12:40 PM | #15 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,390
|
Re: Transmission Reassembly
The aboove quoted post is a platform holder for the tranny so it's easier to work on.
Paul in CT |
09-20-2019, 01:15 PM | #16 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,963
|
Re: Transmission Reassembly
|
09-20-2019, 01:38 PM | #17 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Transmission Reassembly
I have heard not to do that because of the heat and because of the load on the bearing. Is it safe to do?
__________________
"The more things change, the more they stay the same." |
09-20-2019, 01:38 PM | #18 |
Senior Member
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
|
Re: Transmission Reassembly
Also lets be clear and make sure I am putting the bearing on right, so which way is the right way?
__________________
"The more things change, the more they stay the same." |
09-20-2019, 01:48 PM | #19 |
Senior Member
Join Date: Apr 2013
Location: Northwest CT
Posts: 1,092
|
Re: Transmission Reassembly
The face of the bearing that contacts the pressure plate faces out, so you press against that face to get it on the hub. I have used Loctite 609 retaining compound on a couple loose generator bearings with good success. It takes a LOT of heat to break it down. I wouldn't worry about that.
Just FYI, Bert's has good originals for a good price. https://modelastore.com/index.php?ro...roduct_id=3731 |
09-20-2019, 04:00 PM | #20 |
Senior Member
Join Date: Jan 2019
Location: Florida Panhandle
Posts: 585
|
Re: Transmission Reassembly
Something is wrong. Should be a light press fit. Merits further investigation. Hub or bearing would seem to be out of spec.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|