|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-03-2020, 12:51 PM | #1 |
Senior Member
Join Date: Dec 2019
Location: Gardnerville, Nevada
Posts: 185
|
1934 ford front hubs
WHEN I PUT THE FRONT HUB ON WITH SEAL I DONT HAVE ENOUGH THREADS FOR WASHER & NUT. TO INSATLL CARTER KEY?? If I PUT SPINDEL ON WITHOUT SEAL EVERYTHING IS FINE ?? CAN ANYONE HELP!!Thanks Stan
|
03-03-2020, 01:28 PM | #2 |
Senior Member
Join Date: Jun 2010
Location: St Croix Falls WI
Posts: 2,080
|
Re: 1934 ford front hubs
Seal on a 34 front hub ???
Can you post some pics of this " seal " . |
Sponsored Links (Register now to hide all advertisements) |
|
03-03-2020, 02:52 PM | #3 |
Senior Member
Join Date: Dec 2019
Location: Gardnerville, Nevada
Posts: 185
|
Re: 1934 ford front hubs
David I was incorrect, I have a 34 using 37/41 new spindels. After your reply I thought maybe seals are noy required/. without SEALS EVERYTHING WORKS! sTAN
|
03-03-2020, 03:32 PM | #4 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,756
|
Re: 1934 ford front hubs
37-41 does use seals. If you have a non standard setup that may be causing the anomaly.
Try just the seal on it's own on the spindle. Does it ride up on the correct diameter part ok? You'll have to do the detective work on this one. It's impossible to say why it won't go together. Do the brakes match the spindles? Mart. |
03-03-2020, 05:52 PM | #5 |
Senior Member
Join Date: Dec 2019
Location: Gardnerville, Nevada
Posts: 185
|
Re: 1934 ford front hubs
mart the brakes I am using are the reproduction 39 Lincoln. Stan
|
03-03-2020, 06:10 PM | #6 |
Senior Member
Join Date: Dec 2019
Location: Gardnerville, Nevada
Posts: 185
|
Re: 1934 ford front hubs
Sponsored Links (Register now to hide all advertisements)
|
03-03-2020, 06:21 PM | #7 |
Senior Member
Join Date: Dec 2019
Location: Gardnerville, Nevada
Posts: 185
|
Re: 1934 ford front hubs
Mart I just looked up 1937 ford front hub grease seal on the internet. From the looks of picture (I have the wrong Seal) Picture shows a much larger inside diameter which would alow it to go over the larger diameter or sholder and allow bearing to contact the sholder!! Thanks for your help! Stan
|
03-03-2020, 08:09 PM | #8 |
Senior Member
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,835
|
Re: 1934 ford front hubs
correct me if I'm wrong; 34 spindles are longer than 37-41. I think your 39 repop Lincoln backing plates ,whilst they will bolt up to the spindles, the 34 drums will not fit this combo. You'll need later drums
__________________
Unfortunately, two half wits don't make a whole wit! |
03-03-2020, 09:07 PM | #9 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,757
|
Re: 1934 ford front hubs
The 48-1190-A seal should be 2.690 OD and 1.562 ID
Bob |
03-04-2020, 12:07 AM | #10 |
Senior Member
Join Date: Dec 2019
Location: Gardnerville, Nevada
Posts: 185
|
Re: 1934 ford front hubs
Bob C Thank you for Dimensions and part number. That is the seal that I will get, matches my numbers exactly! You have been a lot of help. Thanks again. Stan White
Gardnerville, Nevada 775-265-5333 |
03-04-2020, 12:18 AM | #11 |
Senior Member
Join Date: Dec 2019
Location: Gardnerville, Nevada
Posts: 185
|
Re: 1934 ford front hubs
Brian thanks for the response, I purchased the total reproduction Lincoln Kit it includes everthing for front and rear brakes, Stan I checked the dims on 34/37 spindels the length is the same, my problem was that I had the incorrect Seals.
|
03-04-2020, 01:54 AM | #12 | |
Junior Member
Join Date: Mar 2020
Location: Northern California
Posts: 29
|
Re: 1934 ford front hubs
Quote:
I hope that you and your sweetie are doing great. All the best with your project, Shadowman |
|
03-04-2020, 11:41 PM | #13 |
Senior Member
Join Date: Dec 2019
Location: Gardnerville, Nevada
Posts: 185
|
Re: 1934 ford front hubs
Bill good to hear from you. If you can give me an e mail address I will send you some photos of my project. Stan
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|