|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-21-2018, 04:43 PM | #1 |
Senior Member
Join Date: Dec 2016
Location: Fargo North Dakota
Posts: 264
|
49 ford 6 volt positive ground with pertronic ignition
This car is really hard to start when the engine is cold. The spark is weak while the starter is engaged but very hot spark once the engine is running. I bought the car with the electronic ignition. I have cleaned the grounds, any ideas from the experts out there?
Sent from my SM-T550 using Tapatalk |
11-21-2018, 05:00 PM | #2 |
Senior Member
Join Date: May 2010
Posts: 426
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Using a voltmeter, I would check for voltage drop from the battery negative terminal to the starter terminal and from the battery positive to the case on the starter. The tests will show up bad connections, faulty solenoid switch and cables that are designed for 12v. Make sure you have 6v cables. Find a ammeter that will go over the starter cable while cranking to determine the current draw. If all shows good, you might consider an Optima battery - expensive, but has a long life and will give the starter what it requires. Make sure all of your connections are CLEAN AND TIGHT!!!! I am assuming that the starter is in good condition!!??
|
Sponsored Links (Register now to hide all advertisements) |
|
11-21-2018, 05:11 PM | #3 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Bill pretty much covered it, while you are attempting to start the vehicle the current draw is so large that there is little left over for the ignition.
|
11-21-2018, 05:19 PM | #4 |
Senior Member
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
|
Re: 49 ford 6 volt positive ground with pertronic ignition
And of course you have eliminated fuel starvation as the source of the problem??
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES |
11-21-2018, 05:38 PM | #5 |
Senior Member
Join Date: May 2010
Posts: 426
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Another thought: I use 5W20 Mobil 1. Maybe your oil is to heavy?
|
11-21-2018, 05:49 PM | #6 |
Senior Member
Join Date: Dec 2016
Location: Fargo North Dakota
Posts: 264
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Sponsored Links (Register now to hide all advertisements)
Sent from my SM-T550 using Tapatalk |
11-21-2018, 09:25 PM | #7 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 49 ford 6 volt positive ground with pertronic ignition
I would start by assuring the battery, starter and ground cables are the correct size. It is very common for someone to put a auto parts store cable on these old vehicles and very few of them would carry the correct wire gage. 6v requires about twice the current compared to a 12v system and thus heaver gauge wiring.
|
11-21-2018, 10:24 PM | #8 |
Senior Member
Join Date: Dec 2016
Location: Fargo North Dakota
Posts: 264
|
Re: 49 ford 6 volt positive ground with pertronic ignition
The solenoid to starter cables are original so the correct size. I did put on a new cable from battery to solenoid that is a 0 or 1. I know it should be 00. First thing I will do is clean more terminals and grounds. I have learned over the years not to overlook the simple stuff and charge into the complex things.
Sent from my iPhone using Tapatalk |
11-21-2018, 10:42 PM | #9 |
Senior Member
Join Date: Mar 2016
Location: LaGrande Oregon
Posts: 866
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Maybe check the air gap in the Pertronix module.
|
11-21-2018, 10:51 PM | #10 |
Senior Member
Join Date: May 2010
Location: Columbia, SC
Posts: 1,579
|
Re: 49 ford 6 volt positive ground with pertronic ignition
|
11-21-2018, 11:11 PM | #11 |
Senior Member
Join Date: Jun 2014
Location: Williamsburg, VA
Posts: 1,627
|
Re: 49 ford 6 volt positive ground with pertronic ignition
If there is any green showing on the copper strands entering the connectors, or the copper strands are pinkish, the cable is probably corroded internally and should be replaced, even if it is the proper gauge.
|
11-22-2018, 01:55 AM | #12 |
Senior Member
Join Date: Apr 2015
Location: Sweden
Posts: 3,045
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Check voltage at the battery while cranking to...may be that the battery canīt put out enough amps and then the voltage drops...just saying before you tear the car apart.
|
11-22-2018, 08:08 AM | #13 |
Senior Member
Join Date: Jun 2018
Location: Minnesota
Posts: 347
|
Re: 49 ford 6 volt positive ground with pertronic ignition
|
11-22-2018, 09:38 AM | #14 |
Senior Member
Join Date: May 2010
Posts: 426
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Yes, I have used 20W since 1950 in a flathead and never tossed a bearing. Also used it in farm tractors, farm truck(59AB) and combine. And I used it in a 1980 Olds Diesel that ran to 119K when a collision did it in. Bought it by the barrel.
|
11-22-2018, 08:06 PM | #15 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 49 ford 6 volt positive ground with pertronic ignition
5w20 is not the same as 20w. The "w" stands for "winter" rating, so the 5w is rated at the winter temperature rating and the 20 at the normal high temp rating.
|
11-22-2018, 09:46 PM | #16 |
Senior Member
Join Date: May 2010
Location: Virginia
Posts: 210
|
Re: 49 ford 6 volt positive ground with pertronic ignition
My 6 volt pertronix on my crab distributor ran much better when I replaced the copper core wires with silicone and opened up the sparkplug gap another .005 . pertronix is not telling folks to replace the copper ignition wires for higher capacity silicon/carbon sires.
|
11-22-2018, 09:47 PM | #17 |
Senior Member
Join Date: May 2010
Location: SPEEDWAY INDIANA
Posts: 4,148
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Six volt and positive ground can be pretty touchy with electronics, system has to be perfect to work and have NO voltage drops.......especially while cranking......I would suggest changing back to points on this situation ...
|
11-22-2018, 10:01 PM | #18 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,320
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Finally! Somebody said it. I've been holding my tongue. Thanks, Bubba!
|
11-23-2018, 08:33 AM | #19 |
Senior Member
Join Date: Dec 2016
Location: Fargo North Dakota
Posts: 264
|
Re: 49 ford 6 volt positive ground with pertronic ignition
Thanks to all and for sure bubba. My first step will be check cables and contacts, then go back to points and condenser. It's cold in Fargo but I can work in a heated shop but can test in cold temps.
Sent from my SM-T550 using Tapatalk |
11-23-2018, 10:26 AM | #20 |
Senior Member
Join Date: May 2010
Location: Northeast Pennsylvania
Posts: 1,582
|
Re: 49 ford 6 volt positive ground with pertronic ignition
What coil are you using?
I have a 6V pos gnd Pertronix and had ignition troubles for a long time until I finally got the 0.6 ohm Pertronix ignition coil. Runs great, and sorry Bubba but I'll never go back to points and condensors! |
|
|
Sponsored Links (Register now to hide all advertisements) |
|