|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-02-2022, 10:39 PM | #1 |
Senior Member
Join Date: Dec 2012
Location: San Francisco, CA
Posts: 169
|
Spark plug resistance
Hello,
Is there any known/established upper limit on spark plug resistance, particularly for the inner conductor? I pulled one plug from a cylinder from which I was not getting any significant power (shorting the spark wire to ground did not result in any significant decrease in engine idle rpm). I checked its resistance with a multi-meter, which showed about 1.8k ohms, which seems high to me. Other plugs pulled from cylinders operating as expected showed 0.2 - 8 ohms. Anyone else ever run into this kind of problem? -Andrew B. |
03-02-2022, 11:12 PM | #2 |
Senior Member
Join Date: Mar 2021
Location: Camarillo, Ca
Posts: 167
|
Re: Spark plug resistance
I don't know of any go/no go limit but, like you, I mostly find resistance of the positive electrode in the less than 10 ohm range. I would throw out a plug at 1.8K ohms.
|
Sponsored Links (Register now to hide all advertisements) |
|
03-03-2022, 07:57 AM | #3 |
Senior Member
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,901
|
Re: Spark plug resistance
Interesting. I have never done that. It should be a straight shot with little or no resistance. I think there are resistance plugs for newer cars but I don't think they were ever made for Model A's. The resistive carbon wires for newer cars reduce the amount of electro-magnetic energy coming off the wires and actually deliver more energy to the plugs. But that is another story.
__________________
A is for apple, green as the sky. Step on the gas, for tomorrow I die. Forget the brakes, they really don't work. The clutch always sticks, and starts with a jerk. My car grows red hair, and flies through the air. Driving's a blast, a blast from the past. |
03-03-2022, 08:13 AM | #4 |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: Spark plug resistance
I've never checked the resistance. If one isn't working, I toss in another.
They are quite fragile, a little tap in the wrong place can crack the porcelain which is not easily seen. |
03-03-2022, 10:46 AM | #5 |
Senior Member
Join Date: May 2012
Location: Fredericksburg, Virginia
Posts: 765
|
Re: Spark plug resistance
This a good example for use of the old time Champion spark plug tester. With an air line connected and pressure regulated to equal engine compression, the tester allows you to see how the plug performs under compression. Because air has resistance and higher pressure means more resistance, a plug that fires fine laying against the outside of the engine, may be very weak or not fire at all under compression.
This tester has a model T coil inside. Install the plug, hook up the high tension lead and press the button. The spark is visible through the window via a mirror. |
03-03-2022, 10:54 AM | #6 |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,046
|
Re: Spark plug resistance
Sponsored Links (Register now to hide all advertisements)
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
03-03-2022, 11:30 AM | #7 |
Senior Member
Join Date: May 2010
Location: Santa Rosa, CA
Posts: 1,279
|
Re: Spark plug resistance
Newer Plugs have resistance built in. Google it, There are resistance charts. I would think it would make no difference if your coil is good--it should be able to easiliy overcome 1.8k resistance.
|
03-03-2022, 12:43 PM | #8 |
Senior Member
Join Date: Jun 2010
Location: 34.22 N 118.36 W
Posts: 1,057
|
Re: Spark plug resistance
aside from the resistance on the center electrode, which really is not a concern for the high voltage characteristics of conductivity.
The issue could be more of an insulation leakage to ground thru the insulator. Those are take-apart plugs, not that I recommend taking them apart as routine maintenance, but, you could take apart the one not working and check for burning thru insulator. More than likely there will be a burn scar inside the assembly where the spark is jumping to ground. The real answer is to just replace the plug as there is not much you can do to fix the insulation. Just thoughts, John PS. aircraft plugs are resistor types, typically considered "good" if resistance measures less than 4kohms.
__________________
As Carroll Smith wrote; All Failures are Human in Origin. |
03-03-2022, 01:16 PM | #9 |
Senior Member
Join Date: Sep 2019
Location: Fort Gratiot, Michigan
Posts: 2,296
|
Re: Spark plug resistance
For the insignificant cost of a replacement plug, why not just replace the suspect plug and get on with enjoying the vehicle.
|
03-03-2022, 08:24 PM | #10 |
Senior Member
Join Date: May 2010
Location: Glendale, AZ
Posts: 2,953
|
Re: Spark plug resistance
Your plug connection under the brass top is probably broken.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|